Additional Warnings - Evolution R255SMS-DB Instrucciones Originales

www.evolutionpowertools.com

ADDITIONAL WARNINGS

(These warnings are specified in UL Std. 987 and
CAN/CSA Std.C22.2 No. 71.2)
1. Keep guards in place and in working order.
2. Remove adjusting keys and wrenches. Form
habit of checking to see that keys and adjusting
wrenches are removed from tool before turning it on.
3. Keep work area clean. Cluttered areas and
benches invite accidents.
4. Don't use in dangerous environment. Don't
use power tools in damp or wet locations, or expose
them to rain. Keep work area well lit.
5. Keep children away. All visitors should be kept
safe distance from work area.
6. Make workshop child proof with padlocks,
master switches, or by removing starter keys.
7. Don't force the tool. It will do the job better and
safer at the rate for which it was designed.
8. Use the right tool. Don't force the tool or
attachment to do a job for which it was not designed.
9. Use proper extension cord. Make sure your
extension cord is in good condition. When using an
extension cord, be sure to use one heavy enough to
carry the current your product will draw. An under-
sized cord will cause a drop in line voltage resulting
in loss of power and overheating. The table on the
next page shows the correct size to use depending
on cord length and nameplate ampere rating. If in
doubt, use the next heavier gauge. The smaller the
gauge number, the heavier the cord.
10. Wear proper apparel do not wear loose
clothing, gloves, neckties, rings, bracelets, or other
jewellery which may get caught in moving parts.
Nonslip footwear is recommended. Wear protective
hair covering to contain long hair.
11. Always use safety glasses. Also use face or
dust mask if cutting operation is dusty. Everyday
eyeglasses only have impact resistant lenses, they
are not safety glasses.
12. Secure work. Use clamps or a vise to hold work
when practical. It' s safer than using your hand and it
frees both hands to operate tool.
13. Don't overreach. Keep proper footing and
balance at all times.
14. Maintain tools with care. Keep tools
sharp and clean for best and safest performance.
Follow instructions for lubricating and
changing accessories.
15. Disconnect tools before servicing; when
changing accessories, such as blades, bits, cutters,
and the like.
16. Reduce the risk of unintentional stating. Make
sure switch is in off position before plugging in.
17. Use recommended accessories. Consult the
owner's manual for recommended accessories.
The use of improper accessories may cause risk of
injury to persons.
18. Never stand on the tool serious injury could
occur if the tool is tipped or if the cutting tool is
unintentionally contacted.
19. Check damaged parts. Before further use
of the tool, a guard or other part that is damaged
should be carefully checked to determine that it will
operate properly and perform its intended function
- check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation.
A guard or other part that is damaged should be
properly repaired or replaced.
20. Direction of feed. Feed work into a blade or
cutter against the direction of rotation of the blade
or cutter only.
21. Never leave tool running unattended. Turn
power off. Don't leave the tool until it comes to a
complete stop.
GETTING STARTED - UNPACKING
(4.1)
Caution: This packaging contains sharp objects.
Take care when unpacking. This machine could
require two persons to lift, assemble and move this
machine. Remove the machine, together with the
accessories supplied from the packaging. Check
carefully to ensure that the machine is in good
condition and account for all the accessories listed in
this manual. Also make sure that all the accessories
are complete. If any parts are found to be missing,
the machine and its accessories should be returned
together in their original packaging to the retailer.
Do not throw the packaging away; keep it safe
throughout the warranty period. Dispose of
the packaging in an environmentally
responsible manner. Recycle if possible. Do not let
children play with empty plastic bags due to the risk
of suffocation.
11
EN