XPG CORE REACTOR GOLD SERIE Manual De Instrucciones página 7

INSTALLING YOUR NEW CORE REACTOR POWER SUPPLY
1. Please turn off AC power switch if you are swapping the power supply.
2. Please install your XPG Power Supply in the correct area
3. Please use a screwdriver to install the power supply
Please connect the 18+10pin Modular cable connector to the PSU modular socket
4.
5. Please connect the 20+4 pin MB connector to the 24pin socket on the MB
6. Please connect the CPU 8pin Modular cable connector to the PSU modular CPU power
7. Please connect the 8 or 4 pin CPU connector to the CPU power socket on the MB if
required.
8. Please connect the PCI-E 8pin Modular cable connector to the PSU modular VGA power
socket if required.
9. Please connect the PCI-E 2.0 (6+2pin) Graphic connector to the 6 or 8 pin socket on the
VGA card if required.
10. Please connect the 6pin Modular cable connector to the PSU modular SATA or Molex
power socket if required.
11. Please connect the SATA or Molex Connectors to all the peripherals if required.
12. Please turn on the AC power switch if you have finished your system installation.
TROUBLESHOOTING
If your system does not turn on after installing the power supply, please follow the
troubleshooting guide listed below:
1. Please make sure the AC main power cord is connected to your PC correctly.
2. Please make sure the AC source is switched On
Please make sure the AC On/Off switch on the back panel of the power supply unit in
3.
the "I" (On) position.
4. Please make sure the MB & CPU Power Socket & connectors are connected correctly on
the Motherboard.
5. If you still have problem turning on your PC, please contact ADATA Tech Support,
Service Center or your local dealer.
DURATION OF WARRANTY
ADATA Technology Co., Ltd. provides a 10 years warranty period for this product unless
regional laws and regulations state otherwise.
LIMITATION OF WARRANTY
This limited warranty covers only repairs or replacements of products manufactured by
ADATA Technology Co. Ltd. and its authorized partners.
Please note that ADATA is responsible for providing free repairs except for the following
reasons:
1. The warranty label is altered, damaged or missing.
2. Product serial number does not conform to our original system.
3. Products purchased from an unauthorized agent.
4. Damage caused by natural calamity
5. Any abuse outside the intended product operation.
11
ONLINE CUSTOMER SERVICE
For frequently asked questions, additional information and service instruction please visit
the product page at www.xpg.com
IMPORTANT SAFETY INFORMATION
1. NEVER, under any circumstances, open the power supply unit or attempt to repair the power
supply. This is extremely dangerous due to the high voltage inside.
2. DO NOT insert any objects into the fan grill or the ventilation area of the power supply unit.
3. DO NOT place any objects in front of the fan or the ventilation area of the power supply unit
that may obstruct or restrict the airflow.
4. USE ONLY the modular cables bundled with the power supply unit. DO NOT use any third
party cables or extension cables with this unit.
5. Avoid dust, humidity, and temperature extremes. Do not place the power supply unit in any
area where it may become wet.
6. The power supply unit is for integration into a computer, and not intended for external or
outdoor usage.
7. Failure to comply with any manufacturer instructions and/or any of these safety instructions
will immediately void all warranties and guarantees.
SAFETY AND AGENCY APPROVALS
Agency
EN55032:2012+AC:2013,Class B,EN61000-3-2:2014,EN61000-3-3:
CE
2013,EN55024:2010
CB
IEC 60950-1:2005+A1+A2 or IEC 62368-1:2014
FCC
FCC Part 15 Subpart B Class B
C TUV-US
UL 60950-1 :2007 R10.14,CAN/CSA-C22.2
(American) NO.60950-1-07+A1:2011+A2:2014
TUV
EN 60950-1:2006+A11+A1+A12+A2 or EN 62368-1:2014
IEC 60950-1:2005+A1+A2, or IEC 62368-1:2014, IRAM
TUV-S
2063:2009
2011/65/EU & 2015/863/EU, Restriction of Hazardous Substances
ROHS 2.0
Directive
BSMI
CNS15663、CNS13438、CNS14336-1
CCC
GB4943.1-2011;GB17625.1-2012;GB/T9254-2008
RCM AS/NZS 62368.1.2018,AS/NZS 3112:2011 Inc A1-3
ICES
ICES-003:2016, ANSI C63.4:2014,
2014/35/EU, EN 60950-1:2006+ A11:2009+ A12:2011+
LVD
A1:2010+ A2:2013 or EN 62368-1:2014
CUTR
TP TC 004/2011,TP TC 020/2011
(EAC)
WEEE
2012/19/EU Waste electrical and electronic equipment Directive
Standard
12