Crown CT22016L-2 Manual Original página 24

Symbol
Power tool designation
The power tool has been designed to unscrew and
to tighten threaded fastening elements (bolts, nuts,
screws, bolt screws, etc�)�
Power tool components
1 LED lamp
2 Tool holder
3 Battery lock *
4 Control button of the state of battery charge *
5 Indicators of the state of battery charge *
6 Ventilation slots
7 Reverse switch
8 On / off switch
9 Belt clip *
10 Battery *
11 Pin *
12 Spring *
13 Socket wrench *
14 Charger *
15 Carrying bag *
16 Fixing bush
17 Screwdriver bit *
18 Magnetic holder *
19 Charger label *
20 Indicator (red) *
21 Indicator (green) *
* Optional extra
Not all of the accessories illustrated or described
are included as standard delivery.
Installation and regulation of power tool
elements
Before execution of any procedures, centre the re-
verse switch 7.
Mounting / dismounting / setting-up of
some elements is the same for all power
tool models, in this case specific models
are not indicated in the illustration.
Mounting / replacement of accessories (see
fig. 1-2)
[CT22016L-2, CT22016L-4]
• While mounting, install the socket wrench 13 on the
tool holder 2 as shown on the figure 1.
Meaning
Stepless speed control�
Do not dispose of the power
tool in a domestic waste
container�
• Disassembly operations do in reverse sequen-
ce�
[CT22022L-2, CT22022L-4]
• Move forward the fixing bush 16 and hold it in this
position (see fig. 2).
• Mount / replace the accessory�
• Release the fixing bush 16�
Screwdriver bit / magnetic holder (see fig. 3)
[CT22022L-2, CT22022L-4]
Use accessories that have circular groove at the stem
end, their use will guarantee safe fixation of accessory
in the tool holder 2�
For short screwdriver bits use the magnetic holder 18
for their reliable fixing (see fig. 3).
A magnetic holder 18 is not needed for extended
screwdriver bits 17 (specially purposed for screwdriv-
ers)�
Charging procedure of the power tool
battery
Initial operating of the power tool
The power tool is supplied with a partially charged
battery 10. Before the first use, the battery 10 must
be fully charged.
Charging process (see fig. 4-5)
• Centre the reverse switch 7�
• Press the battery lock 3 and remove the battery 10
(see fig. 4.1, 5.1).
• Connect the charger 14 to the power supply�
• Insert battery 10 into charger 14 (see fig. 4.2, 5.2).
• Disconnect the charger 14 from power supply after
charging�
• Remove the battery 10 from the charger 14 and
mount battery 10 in the power tool (see fig. 4.3, 5.3).
Charger indicators (see fig. 6)
Charger indicators 20 and 21 inform of the battery 10
charging process� Signals of the indicators 20 and 21
are shown on the label 19 (see fig. 6).
• Fig� 6�1 - (the green indicator 21 is on, the battery 10
is not inserted in the charger 14) - the charger 14 is
connected to the power network (ready for charging)�
• Fig� 6�2 - (the red indicator 20 is on, the battery 10
is inserted in the charger 14) - the battery 10 is being
charged�
• Fig� 6�3 - (the green indicator 21 is on, the battery 10
is inserted in the charger 14) - the battery 10 is fully
charged�
In the process of charging the battery 10
and the charger 14 become hot, it is a
normal process.
Switching the power tool on / off
Make sure that the reverse switch 7 is not centred,
this blocks on / off switch 8.
English
24