Troubleshooting Guide - Heath Zenith Dual Brite SL-5597 Guia De Inicio Rapido

Page 4
If you experience a problem with your Light Control, first follow this guide. You may also want to visit our Web site
at: www.desatech.com. For additional assistance call 1-800-858-8501 7:30 AM to 4:30 PM Central Time,
weekdays.
SYMPTOM POSSIBLE CAUSE
Lights will 1. Light switch is turned off.
not come on. 2. Light is loose or burned out.
3. Fuse is blown or circuit breaker is turned off.
4. Daylight turnoff is in effect (recheck after
dark) .
5. Incorrect circuit wiring, if this is a new
installation.
6. Re-aim the sensor to cover desired area.
1. Light Control may be installed in a rela-
Lights come
tively dark location.
on in day-
2. Light Control is in Test. (Set control switch
light.
to an ON-TIME position) .
1. Light Control may be sensing small ani-
Lights come
mals or automobile traffic (re-aim sensor) .
on for no
2. Range is set too high. (Reduce Range
a p p a r e n t
setting) .
reason.
3. Dual Brite™ Timer is on.
Lights turn
1. Sensor is in a relatively dark location. (Re-
off too late in
locate sensor, or use 3 hr or 6 hr setting) .
D u s k - t o -
Dawn setting.
This is a "Limited Warranty" which gives you specific legal rights. You may also have other rights which vary from state to state
or province to province.
For a period of ten year from the date of purchase, any malfunction caused by factory defective parts or workmanship will be
corrected at no charge to you. Light bulbs are not covered. To obtain a refund or a replacement, return the product to the
place of purchase.
Not Covered - Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs and other expendable
items are not covered by this warranty. Unauthorized service or modification of the product or of any furnished component will
void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation, setup time, loss
of use, or unauthorized service.
This warranty covers only Heath
a customer uses in conjunction with our products.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY
WARRANTY, REPRESENTATION OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT FOR
ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES.
REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE SHALL BE NO LIABILITY
ON THE PART OF DESA FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING
BUT NOT LIMITED TO ANY LOSS OF BUSINESS OR PROFITS, WHETHER OR NOT FORESEEABLE. Some states or
provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to you. Retain receipt for warranty claims.

TROUBLESHOOTING GUIDE

YOUR HEATH ® /ZENITH TEN YEAR LIMITED WARRANTY
® /Zenith assembled products and is not extended to other equipment and components that
SYMPTOM
POSSIBLE CAUSE
Lights stay on 1. A lamp is positioned too close to the sensor or
continuously. pointed at nearby objects that cause heat to
trigger the sensor. (Reposition the lamp away
from the sensor or nearby objects) .
2. Light Control is pointed toward a heat source
like an air vent, dryer vent, or brightly-painted
heat-reflective surface. (Reposition sensor.
Reduce Range) .
3. Light Control is in Manual Mode. (Switch to Auto) .
Lights flash
1. Heat or light from the lamps may be turning the
on and off.
Light Control on and off. (Reposition the lamps
away from the sensor) .
2. Heat being reflected from other objects may be
affecting the sensor. (Reposition sensor) .
3. Light Control is in the Test mode and warming
up. (Flashing is normal under these conditions.
Turn Boost off) .
1. Sensor is detecting its own lights. (Reposi-
Lights flash
tion lamps to keep area below the sensor
once, then
relatively dark).
stay off in
Manual Mode.
595-5679-05