Casals VML200 Manual Del Usuario página 5

et, or - Let the appliance running with no load for 30 seconds
in a safe position. If you notice serious vibration or other
. defects stop the appliance immediately. Then check the
problem and /or proceed as we describe on Anomalies
ngled and Repair clause.
- Apply the machine to the workpiece only when
switched on and switch the machine off only after it
has been lifted away from the workpiece. The power
while tool can move suddenly.
- Pay attention that no persons are put at risk through
Work- sparking. Remove any combustible materials in the
duced vicinity. Sparking occurs when sanding metal materials.
types - Caution, fire hazard! Avoid overheating the object
safety being sanded as well as the sander. Always empty
the dust collector before taking breaks. In unfavour-
ion of able conditions, e. g., when sparks emit from sanding
d sur- metals, sanding debris in the dust bag, micro filter or
nt that paper sack (or in the filter sack or filter of the vacuum
ations. cleaner) can self-ignite. Particularly when mixed with
ration remainders of varnish, polyurethane or other chemical
m the materials and when the sanding debris is hot after long
periods of working.
each - Regularly clean the power tool's air vents. The
motor's fan will draw the dust inside the housing and
ncing excessive accumulation of powdered metal may cause
ea. electrical hazards.
m the - Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than
prop- by hand.
con- Product description and Specifications
them
Description (Fig. A, B, C, D, E, F, G)
not in
1 On/Off Switch
2 Dust collector with microfilter System
acing
3 Sanding sheet
4 Sanding plate
rofes-
5 Buttons to rotate base
6- Filter connector
at this
7- Filter lid
eople
8- Filter element
9- Dust tank
super-
10- Dust extraction adapter
ance.
ures.
of di-
Instructions for use
nd re- Before use:
rews, - Make sure that all the product's packaging has been
removed.
se. - Ensure that the voltage indicated on the rating label
y of a matches the mains voltage before plugging in the
appliance.
Integrated dust extraction with microfilter (Fig A)
- Always use the appliance with the dust collector (2)
connected, inhaling dust is harmful to your health.
- Connect the dust collector (2) to the filter connector (6)
Empty the dust collector (Fig D, E, F, G)
- To empty the dust collector pull off the dust collector (2)
- Remove the filter lid (7) pulling it as it's shown in the
fig (E).
- Remove the Filter element (8) from the Dust tank.
- Clean the filter element (8) and the dust tank (9) with
a soft brush.
External Dust extraction (Fig G)
- Connect dust extraction adaptor (10) on the filter
connector (6).
- Connect the vacuum aspirator suction tube to the dust
extraction adaptor (10).
Replacing the sanding Sheet (Fig B)
- To remove the sanding sheet (3) grasp it at one of the
tips and pull it off from the sanding plate (4).
- Pay attention that punched holes of the abrasive sheet
(3) match with the holes of the sanding plate (4).
- Position the sanding sheet (3) flush alongside one edge
of the sanding plate (4).
- Lay the sanding sheet onto the sanding plate and press
firmly.
- To remove the sanding sheet (3) grasp it at one of the
tips and pull it off from the sanding plate (4).
Rotate the sanding plate (Fig C)
- To rotate the base push simultaneously the 2 buttons (5)
on the sanding plate (4).
- Rotate the sanding plate (4) until the desired position.
- Release the pressure on the buttons to rotate the base (5).
Switch on y Switch off (Fig A)
- Turn the appliance on, by using the on/off button (1)
- Turn the appliance off, by using the on/off button (1)
Use:
- Unroll the cable completely before plugging it in.
- Connect the appliance to the mains.
- Assemble the sanding Sheet
- Turn the appliance on, by using the on/off button (1).
- Place the appliance against the surface you want to
work.
- Slowly move the appliance over the workpiece,
- Do not apply excessive pressure against the workpiece.
- Apply uniform sanding pressure against the workpiece
to increase performance and working life of the sander
and the sanding sheet.
5