Cautions On Handling Discs; Connections - Denon Professional DN-V200 Instrucciones De Operación

ENGLISH
3

CAUTIONS ON HANDLING DISCS

Discs
Only the discs including the marks shown on page 5
can be played on the DN-V200/DN-V300.
Note, however, that discs with special shapes (heart-
shaped discs, hexagonal discs, etc.) cannot be played
on the DN-V200/DN-V300. Do not attempt to play
such discs, as they may damage the player.
Holding Discs
Avoid touching the surface of discs when loading and
unloading them.
Be careful not to get
fingerprints on the signal
surface (the side which
shines in rainbow colors).
Cleaning Discs
Fingerprints or dirt on the disc may lower sound
2
and picture quality or cause breaks in playback.
Wipe off fingerprints or dirt.
Use a commercially available disc cleaning set or a
2
soft cloth to wipe off fingerprints or dirt.
Wipe gently from the Do not wipe with a circular
middle outwards. motion.
NOTE:
• Do not use record spray or antistatic. Also do
not use volatile chemicals such as benzene or
thinner.
Record Thinner Benzene
spray
6
Cautions on Handling Discs
• Do not get fingerprints, grease or dirt on discs.
• Be especially careful not to scratch discs when
removing them from their cases.
• Do not bend discs.
• Do not heat discs.
• Do not enlarge the center hole.
• Do not write on the labeled (printed) side with a ball-
point pen or a pencil.
• Water droplets may form on the surface if the disc
is moved suddenly from a cold place to a warm one.
Do not use a hairdryer, etc., to dry the disc.
Cautions on Storing Discs
• Always eject discs after playing them.
• Keep discs in their cases to protect them from dust,
scratches and warping.
• Do not put discs in the following places:
1. Places exposed to direct sunlight for long periods
of time
2. Humid or dusty places
3. Places exposed to heat from heaters, etc.
Cautions on Loading Discs
• Only load one disc at a time. Loading one disc on
top of another may result in damage or scratch the
discs.
• Load 8 cm discs securely in the disc guide, without
using an adapter. If the disc is not properly loaded, it
may slip out of the guide and block the disc tray.
• Be careful not to let your fingers get caught when
the disc tray is closing.
• Do not place anything but discs in the disc tray.
• Do not load cracked or warped discs or discs that
have been fixed with adhesive, etc.
• Do not use discs on which the adhesive part of
cellophane tape or glue used to attach the label is
exposed, or discs with traces of tape or labels that
have been peeled off. Such discs may get stuck
inside the player, resulting in damage.
4

CONNECTIONS

• Read the manuals of all the components when
making connections.
• Keep the power cord unplugged until all
connections have been completed.
• If the power is on when connections are made,
noise may be generated and damage the
speakers.
(1) Connecting a TV
• Use the included audio video cord to connect the TV's video input connector and audio input connectors to
the DN-V200/DN-V300's VIDEO OUT or S-VIDEO OUT and AUDIO OUT.
• Check that "P.SCAN" on the front panel display is off. If "P.SCAN" is lit, press the "SHIFT" and "P.SCAN"
button on the front panel so that "P.SCAN" turns off. Pictures are not output properly if "P.SCAN" is lit.
• To use with s-video output, set in "VIDEO OUT" in "VIDEO SETUP" in "SETUP" at the initial settings.
(See page 14)
S-Video output connector
The video signals are divided into color (C) and
brightness (Y) signals, achieving a clearer picture.
If the TV is equipped with an S-Video input connector,
we recommend connecting it to the DN-V200/DN-
V300's S-Video output connector using a
commercially available S-Video connection cord.
TV
VIDEO IN
AUDIO IN
S-VIDEO IN
L R
• Connect the DN-V200/DN-V300's video outputs to
the TV either directly or through an AV amplifier.
Do not connect it via a VCR (video cassette
recorder). Some discs contain copy prohibit
signals. If such discs are played via a VCR, the
copy prohibit system may cause disturbance in
the picture.
• Set the "TV TYPE" in "VIDEO SETUP" in
"SETUP" to comply with your TV's video format.
When the TV is PAL formatted, set to PAL.
(See page 14.)
NOTES:
• Be sure to connect the left and right channels
properly, L (left) to L, R (right) to R.
• Plug the power cord securely into the power
outlet. Incomplete connection may result in noise.
• Binding the power cord together with connection
cords may result in humming or noise.
DN-V200/DN-V300
To power outlet
NOTES:
• Set the "TV ASPECT" in "VIDEO SETUP" in
"SETUP" to comply with your TV's aspect. (See
page 13)
• No audio signals are output from the DN-
V200/DN-V300's "AUDIO OUT" connector when
discs recorded in DTS are played.