Silverline Silver Storm 264782 Manual De Instrucciones página 7

264782
Operation
WARNING: ALWAYS wear eye protection, adequate respiratory and hearing
protection, as well as suitable gloves, when working with this tool.
• Once plugged into the mains power source, the hoist will be ready for operation
• Never move the Operating Switch (2) directly between
moved into the central 'off' position between each up or down operation
• If the hoist is unable to lift the load, stop immediately as it is overloaded
Loading the Hoist
• Before loading ensure the hoist is positioned directly over the load. Failure to do
so could result in the load swinging freely once elevated
• Ensure the load is free to move and is not restricted by anything. If the load
is restricted this will cause the hoist to overload and potentially cause severe
damage. This may also invalidate the warranty
• The load must be firmly and securely attached to the Lifting Hook (11) of the
hoist
• If using a cargo sling to aid in the lifting of the load: ensure the sling is
sufficiently supporting the load, and the load is properly centred in the sling
NOTE: Ensure that the Operating Switch is in the off position so that the hoist will
not attempt to lift the load whilst being connected.
Lifting the Load
1. When the load is correctly attached, remove the cable slack slowly by moving
the Operating Switch (2) into the position
2. When the slack has been removed, ensure that there are no persons within a
5m radius of the load being lifted
3. Press the operating switch into the
NOTE: Be aware of the maximum lifting capacities and height limitations stated
in the specifications.
• When the hoist reaches its height limitation it will automatically switch off
Lowering the Load
1. Before attempting to lift the load, ensure that whatever you plan to lower the
load onto is capable of supporting the load, and that it is sufficiently stable and
ready to be loaded
2. Lower the load by pressing the Operating Switch (2) into the
3. Gently lower the load ensuring that the load stabilises
4. Lower the Lifting Hook (11) an extra 30cm to ensure there is enough cable slack
to disconnect the loading hook and raise the Lifting Hook clear of the load
NOTE: When raising the Lifting Hook clear, ensure the Cable (9) winds onto the
spool correctly and does not cross over itself.
WARNING: If at any point during the hoist's operation someone enters the
operating area or the load becomes unstable, press the Emergency Stop Button (3)
immediately. To release the Emergency Stop Button rotate it clockwise.
Accessories
• A range of accessories and consumables, including Hoist Support Arm (407455),
1m Cargo Sling 1 Tonne (633720), 2m Cargo Sling 1 Tonne (868705), Safety
Hard Hat (306429), and Expert Rigger Gloves (633501), is available from your
Silverline stockist. Spare parts can be obtained from toolsparesonline.com
Maintenance
WARNING: ALWAYS disconnect from the power supply before carrying out
any inspection, maintenance or cleaning.
General inspection
• Regularly check that all the fixing screws are tight
• Inspect the supply cord of the tool, prior to each use, for damage or wear.
Repairs should be carried out by an authorised Silverline service centre. This
advice also applies to extension cords used with this tool
Cleaning
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear
quickly, and shorten the machine's service life. Clean the body of your machine
with a soft brush, or dry cloth. If available, use clean, dry, compressed air to
blow through the ventilation holes
• Clean the tool casing with a soft damp cloth using a mild detergent. Do not use
alcohol, petrol or strong cleaning agents
• Never use caustic agents to clean plastic parts
. The switch must be
to lift the load to its required position
position
Lubrication
• Slightly lubricate all moving parts at regular intervals with a suitable spray
lubricant
Brushes
• Over time the carbon brushes inside the motor may become worn
• Excessively worn brushes may cause loss of power, intermittent failure, or
visible sparking
• If you suspect that the brushes may be worn, have them replaced at an
authorised Silverline service centre
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
Disposal
Always adhere to national regulations when disposing of power tools that are no
longer functional and are not viable for repair.
• Do not dispose of power tools, or other waste electrical and electronic
equipment (WEEE), with household waste
• Contact your local waste disposal authority for information on the correct way
to dispose of power tools
www.silverlinetools.com
500W Electric Hoist
7