Using The Shaver - Braun 5 Serie Manual

Our products are designed to meet the highest
standards of quality, functionality and design.
Thank you for your trust in Braun's quality and we
hope you enjoy your new Braun shaver.
This appliance is designed for household use only.
Shaver
1 Foil & Cutter cassette
2 Cassette release button
3 MultiHeadLock switch
4 On/off switch
5 Shaver display
6 Long hair trimmer
7 Shaver-to-station contacts
8a Release button for long hair trimmer
8b Model number of shaver
9 Shaver power socket
10 Special cord set
11a Brush
11b Hard travel case*
11c Protection cap*
*not with all models
First use and Charging
Prior to first use remove the protection foil if any
from the shaver display and connect the shaver to
an electrical outlet using the special cord set (10).
Charging and basic operating information
• A full charge provides up to 45 minutes of cordless
shaving time. This may vary according to your
beard growth and environmental temperature.
• Recommended ambient temperature for charging
is 41 °F to 95 °F / 5 °C to 35 °C. The battery may not
charge properly or at all under extreme low or high
temperatures. Recommended ambient temperature
for shaving is 60 °F to 95 °F / 15 °C to 35 °C.
• Do not expose the shaver to temperatures higher
than 122 °F / 50 °C for extended periods of time.
• When the shaver will be connected to an electrical
outlet, it may take some minutes until the display
illuminates.
Shaver display
Charge status
The shaver display (5) shows the charge status of
the battery.
During charging: The battery symbol will blink.
(5090cc: The respective battery segment will blink.)
Fully charged (shaver is connected to an electrical
outlet): The battery symbol will light up for a few
seconds. (5090cc: All battery symbols will light up
for a few seconds.)
Low charge
The low-charge light
battery is running low. You should be able to finish
flashes red when the
your shave. With switching off the shaver a beep
sound reminds of the low charge status.
Cleaning status
(models 5090cc/5070cc/5050cc only)
The cleaning indicator
needs to be cleaned in the Clean&Charge Station.
Travel lock
The lock symbol lights up when the shaver has
been locked to avoid unintended starting of the
motor (e.g. for storing it in a suitcase).

Using the shaver

Press the on/off switch (4) to operate the shaver.
Tips for a perfect dry shave
For best results, Braun recommends you to follow
3 simple steps:
1. Always shave before washing your face.
2. At all times, hold the shaver at the right angle
(90°) to your skin.
3. Stretch your skin and shave against the direction
of your beard growth.
MultiHeadLock switch (head lock)
To shave hard-to-reach areas (e.g. under the nose)
slide the MultiHeadLock switch (3) down to lock the
shaver head. The shaver head can be locked in five
positions. To change position, move the shaver head
with your thumb and forefinger back or forth. It will
automatically click into the next position.
To set it back into the pivoting position the
MultiHeadLock switch needs to be slid up again.
Models 5090cc/5070cc/5050cc: For automatic
cleaning in the Clean&Charge Station the head lock
should be released.
Long hair trimmer
To trim sideburns, moustache or beard press the
release button (8a) and slide the long hair trimmer
(6) upwards.
Shaving with the cord (models 5090cc/5070cc/
5050cc/5030s/5020s only)
If the shaver has run out of power (discharged), you
may also shave with the shaver connected to an
electrical outlet via the special cord set.
Travel lock
• Activation: By pressing the on/off switch (4) for
3 seconds the shaver is locked. This is confirmed
by a beep sound and the lock symbol
display. Afterwards the display turns off.
• Deactivation: By pressing the on/off switch for
3 seconds the shaver is unlocked again.
lights up, when the shaver
(see fig. A)
in the
9