Technical Data - Milwaukee DD2-160 XE Manual Original

TECHNICAL DATA

DIAMOND DRILL
Production code.......................................................................
..............................................................................................
..............................................................................................
Rated input ..............................................................................
Output ......................................................................................
No-load speed, 1st gear ..........................................................
No-load speed, 2nd gear .........................................................
Speed under load max., 1st gear ............................................
Speed under load max., 2nd gear ...........................................
Percussion rate max. ...............................................................
Drilling capacity, 1st gear .........................................................
Drilling capacity, 2nd gear .......................................................
Drive shank..............................................................................
Chuck neck diameter ...............................................................
Weight according EPTA-Procedure 01/2003 ...........................
Noise information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) ........................
Sound power level (Uncertainty K=3dB(A)) .............................
Wear ear protectors!
Vibration information
Vibration total values (triaxial vector sum) determined
according to EN 60745
Vibration emission value a
h
Drilling into metal ..................................................................
Uncertainty K= ......................................................................
Impact drilling into concrete ..................................................
Uncertainty K= ......................................................................
Impact drilling into concrete with dry diamond core cutter ....
Uncertainty K= ......................................................................
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given
in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration emission may differ. This may signifi cantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
WARNING! Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in
electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
PERCUSSION DRILL SAFETY WARNINGS
Wear ear protectors when impact drilling. Exposure to
noise can cause hearing loss.
Use auxiliary handle(s), if supplied with the tool. Loss of
control can cause personal injury.
Hold the power tool by insulated gripping surfaces only,
when performing an operation where the cutting
accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and could give
the operator an electric shock.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
The built-in friction clutch only reacts to jerky locking, which
is why you should always use the additional handle.
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is
recommended, such as dust mask, protective gloves, sturdy
non-slip footwear, helmet and ear defenders.
16 ENGLISH
DD2-160 XE
..................... 3687 01 01...
..................... 3686 91 01...
..................... 3687 06 01...
...000001-999999
.......................1500 W
.........................820 W
....................0-1500 min
-1
....................0-3000 min
-1
.........................890 min -1
.......................1770 min -1
.....................48000 min -1
....................80-162 mm
......................32-90 mm
........................M18
...........................57 mm
..........................4,2 kg
.........................100 dB (A)
......................... 111 dB (A)
..........................2,3 m/s 2
..........................1,5 m/s 2
........................18,3 m/s 2
..........................1,5 m/s 2
........................14,8 m/s 2
..........................1,5 m/s
2
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Wear a suitable dust
protection mask.
Do not machine any materials that present a danger to
health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls!
Do not switch the device on again while the insertion tool is
stalled, as doing so could trigger a sudden recoil with a high
reactive force. Determine why the insertion tool stalled and
rectify this, paying heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
• when changing tools
• when setting the device down
Chips and splinters must not be removed while the machine
is running.
Keep mains lead clear from working range of the machine.
Always lead the cable away behind you.
When working in walls ceiling, or fl oor, take care to avoid
electric cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped
workpieces can cause severe injury and damage.
Always disconnect the plug from the socket before carrying
out any work on the machine.
When working with large drill diameters, the auxiliary handle
must be fastened in a right angle with the main handle (see
illustrations, section "Twisting the handle").
SPECIFIED CONDITIONS OF USE
The diamond drill can be used to drill with diamond dry drill
bits. With drill chuck mounted the machine is suitable for
percussive drilling in rock and drilling holes in wood and
steel. The machine is not suitable for wet drilling in concrete.
Do not use this product in any other way as stated for
normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under "Technical Data" fulfi lls all the relevant
provisions of the directives 2011/65/EU (RoHs), 2004/108/
EC, 2006/42/EC and the following harmonized standards
have been used:
EN 60745-1:2009 + A11:2010
EN 60745-2-11:2010
EN 55014-1:2006 + A1:2009 + A2:2011
EN 55014-2:1997 + A1:2001 + A2:2008
EN 61000-3-2:2006 + A1:2009 + A2:2009
EN 61000-3-3:2008
EN 50581:2012
Winnenden, 2014-10-22
Alexander Krug
Managing Director
Authorized to compile the technical fi le
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
MAINS CONNECTION
Appliances used at many different locations including wet
room and open air must be connected via a residual current
device (FI, RCD, PRCD) of 30mA or less.
Connect only to single-phase AC current and only to the
system voltage indicated on the rating plate. It is also
possible to connect to sockets without an earthing contact
as the design conforms to safety class II.
Make sure the machine is switched off before plugging in.
PROTECTION OF MOTOR IN CASE OF OVERLOAD
Motor protection device controlled by motor load. The
machine will slowly continue to run in order to cool the motor
down. After suffi cient cooling machine can be restarted by
switching off and on again.
SOFT PERCUSSION
Depending on the material that is to be machined, soft
percussion may result in a sharp reduction in drilling time or
a longer tool life for the diamond segments.
WORKING INSTRUCTIONS
To gain a better drill progress take out the centre bit after
having reached a depth of about 10-15 mm. Insert core
cutter into the existing groove and let machine run up
smoothly.
Bore-holes which don't have to be applied exactly can be
drilled without a centre bit. For that purpose apply the core
cutter slantingly and put the machine slowly straight when a
depth of about 5 mm has been reached. (This is only
possible when using short core cutters!)
If drill cores should come loose, take core cutter from the
material and remove drill cores.
For best performance the diamond segments should be
"roughed-up" to expose the fragments of diamond: To
expose the diamond fragments rub surface of segments
with stone
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
If the machine is mainly used for percussion drilling,
regularly remove collected dust from the chuck. To remove
the dust hold the machine with the chuck facing down
vertically, and completely open and close the chuck. The
collected dust will fall from the chuck.
It is recommended to regularly use cleaner for the clamping
jaws and the clamping jaw borings.
If the supply cord of this appliance is damaged, it must only
be replaced by a repair shop appointed by the manufacturer,
to avoid hazardous situations.
Use only Milwaukee accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our Milwaukee service
agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the Article No. as well as the machine type
printed on the label and order the drawing at your local
service agents or directly at: Techtronic Industries GmbH,
Max-Eyth-Straße 10, 71364 Winnenden, Germany.
ENGLISH 17