Publicidad
Idiomas disponibles
Idiomas disponibles
2
DISASSEMBLY
2.1 Remove the left front cheek pad flap between the chin guard and the base edge trim (Fig. 10 B).
2.2 Remove the wind protector clockwise as shown in Fig. 9 B.
2.3 Insert the left front cheek pad flap between the chin guard and the base edge trim (Fig. 10 B).
WARNING!!!
The Wind Protector is easily removable. You can check the correct assembly of this accessory by pulling it gently towards the inner
part of the helmet with your thumb and forefinger. If it moves, repeat the assembling steps.
•
REMOVABLE INNER COMFORT PADDING
(Only for versions equipped with removable inner padding)
To remove and/or reassemble the inner comfort padding, lift the VPS (Fig 6 A).
1
REMOVAL
1.1 Pull up the visor and unfasten the chin strap (see relative instructions).
1.2 Take hold of the left cheek pad and pull towards the inside of the helmet to undo the snap fasteners on the back. Pull out the side
flap located between the sealing edge and the inner shell, detach all of the cheek pad from the helmet (Fig. 10 A).
1.3 Repeat steps 1.2 on the right cheek pad.
1.4 Release the left rear fastening flap from the support fixed to the inner shell by slightly deforming the shell sealing edge and slight-
ly pulling the comfort padding in the helmet neck-ring area towards the inside (Fig. 11).
Then repeat the same steps to remove the central flap as well as the right rear flap.
1.5 Hold the left front part of the liner and pull it upwards in order to remove the liner flap from the support fixed to the inner poly-
styrene shell (Fig. 12). Repeat the same steps to remove the right and central front flap.
1.6 Completely remove the liner from the helmet.
2
ASSEMBLY
2.1 Insert the liner correctly into the helmet and fit it well against the base.
2.2 Insert the left front flap into the seat on the support fixed to the polystyrene inner shell and push it slightly downwards until it is
completely locked (Fig. 12). Follow the same steps for the right and central front flap.
2.3 Insert the rear right, central and left flaps of the liner into the relevant support seats in the helmet neck-ring area (Fig. 11). To per-
form this step, act as follows: Slightly deform the shell sealing edge and push the flaps until they are completely hooked to the
support.
2
DISASSEMBLY
2.1 Remove the left front cheek pad flap between the chin guard and the base edge trim (Fig. 10 B).
2.2 Remove the wind protector clockwise as shown in Fig. 9 B.
2.3 Insert the left front cheek pad flap between the chin guard and the base edge trim (Fig. 10 B).
WARNING!!!
The Wind Protector is easily removable. You can check the correct assembly of this accessory by pulling it gently towards the inner
part of the helmet with your thumb and forefinger. If it moves, repeat the assembling steps.
•
REMOVABLE INNER COMFORT PADDING
(Only for versions equipped with removable inner padding)
To remove and/or reassemble the inner comfort padding, lift the VPS (Fig 6 A).
1
REMOVAL
1.1 Pull up the visor and unfasten the chin strap (see relative instructions).
1.2 Take hold of the left cheek pad and pull towards the inside of the helmet to undo the snap fasteners on the back. Pull out the side
flap located between the sealing edge and the inner shell, detach all of the cheek pad from the helmet (Fig. 10 A).
1.3 Repeat steps 1.2 on the right cheek pad.
1.4 Release the left rear fastening flap from the support fixed to the inner shell by slightly deforming the shell sealing edge and slight-
ly pulling the comfort padding in the helmet neck-ring area towards the inside (Fig. 11).
Then repeat the same steps to remove the central flap as well as the right rear flap.
1.5 Hold the left front part of the liner and pull it upwards in order to remove the liner flap from the support fixed to the inner poly-
styrene shell (Fig. 12). Repeat the same steps to remove the right and central front flap.
1.6 Completely remove the liner from the helmet.
2
ASSEMBLY
2.1 Insert the liner correctly into the helmet and fit it well against the base.
2.2 Insert the left front flap into the seat on the support fixed to the polystyrene inner shell and push it slightly downwards until it is
completely locked (Fig. 12). Follow the same steps for the right and central front flap.
2.3 Insert the rear right, central and left flaps of the liner into the relevant support seats in the helmet neck-ring area (Fig. 11). To per-
form this step, act as follows: Slightly deform the shell sealing edge and push the flaps until they are completely hooked to the
support.
9
9
Publicidad
