Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
OPERATING INSTRUCTIONS
Winding & Unwinding the
Power Cord
This vacuum cleaner
is equipped with a
convenient cord
storage feature. The
power cord winds
around the two cord
holders at the side
of the unit. The top
cord holder has a
quick cord release
feature. Turn the
cord hook to the left
or the right to
remove the power
cord. (Fig. 12)
Fig. 12
Emptying the Dust Cup Container
WARNING:
Always unplug the
unit from electrical outlet before
opening the dust cup (container).
Important:
Do NOT use the vacuum
without the HEPA filter in place.
1. To remove the
dust cup
container,
press the dust
cup release
button and
remove the
dust cup
container.
(Fig. 13)
2. To empty the dust
cup container, hold the
dust cup from the
handle over a garbage
container and press on
the trap door release
button that is on the
back side of the dust
cup container to
release the dust cup
bottom. (Fig. 14)
Fig. 14
Cleaning the HEPA Dust Cup Filter
WARNING:
After each Use -
Always remove the Filter
Assembly, then vigorously "TapClean"
the HEPA filter and clean debris screen
until no more dust can be removed.
Important, Please Note:
Rinseable "TapClean" HEPA dust cup
filter will stop most of the tiniest dust
particles from re-entering the air you
breathe. Because of this incredible
filtration performance, the HEPA dust
cup filter will quickly accumulate many
fine dust particles inside the white filter
folds that are difficult to see but which
will eventually block or reduce your
suction power - if not cleaned properly.
Clean the HEPA filter after each use as
described in this section.
1. To remove the HEPA
filter, remove the dust
cup container from
the unit.
2. To remove the dust
cup cover, hold the
Fig. 13
dust cup container
by the handle, turn
counter clockwise
and lift the dust cup
cover off. (Fig. 15)
3. Remove the HEPA
Rinseable "Tap
Clean" filter from the
dust cup. (Fig. 16)
4. Vigorously "Tap
Clean" the HEPA
dust cup filter on a
hard surface until no
more dust is
observed falling
out. (Fig. 17)
Fig. 17
6
5. The HEPA filter may
also be washed by
running it under
the tap allowing
the water to run on
the dirty side.
(Fig. 18) We
The
recommend
washing it once a
month or when
suction appears reduced. Always
allow 24 hours for air drying before
replacing into the vacuum.
Please Note: The white material in the
HEPA filter will discolor over time - This is
NORMAL and will NOT affect the
performance of the filter.
WARNING:
dust cup - remove dirt and clean
Fig. 15
the HEPA dust cup filter and debris
screen each time the dust cup is
emptied during prolonged usage or risk
motor damage.
Cleaning the HEPA Filter Frame
1. Before replacing the
HEPA filter in the
HEPA filter frame,
you can (should) rinse
the frame in lukewarm
water by just running it
under the tap to
remove any dust that is adhering
to the frame. (Fig. 19) Do NOT
place in dishwasher.
2. Make sure that the filter frame is
completely dry before replacing into
the dust cup. Always air dry for 24
hours.
Fig. 16
OPERATING INSTRUCTIONS
Cleaning the Pre-Motor Filters
1. Underneath the dust cup container,
are two pre-motor filters. (Fig. 20)
2. One is small and it fits into the air inlet
pipe.
3. To remove, just lift out.
4. To remove the second pre-motor
filter, twist the pre-motor filter cover,
Fig. 18
lift the cover out and remove the
second pre-motor filter. (Fig. 20)
Fig. 20
Never over fill the
5. To clean the pre-motor filters, rinse
in lukewarm water and let air dry
completely for 24 hours. Do not use
a washing machine to rinse the
Fig. 19
filters. Do not use a hair dryer to
dry them. Air dry only.
Never operate the
vacuum cleaner without
all filters in place.
6. We recommend washing
the pre-motor filters when
you are washing your
HEPA filter. (Fig. 21)
7
Pre-
Motor
Filter
Cover
Fig. 21
Publicidad
Tabla de contenido
