Product Description And Specifications; Intended Use - Bosch HWS 0 602 301 4 Serie Manual Original

OBJ_BUCH-2487-002.book Page 25 Wednesday, November 2, 2016 4:43 PM
yond the sanding pad presents a laceration hazard and
may cause snagging, tearing of the disc, or kickback.
Safety warnings specific for polishing operations
 Do not allow any loose portion of the polishing bonnet
or its attachment strings to spin freely. Tuck away or
trim any loose attachment strings. Loose and spinning
attachment strings can entangle your fingers or snag on the
workpiece.
Safety warnings specific for wire brushing operations
 Be aware that wire bristles are thrown by the brush
even during ordinary operation. Do not overstress the
wires by applying excessive load to the brush. The wire
bristles can easily penetrate light clothing and/or skin.
 If the use of a guard is recommended for wire brushing,
do not allow any interference of the wire wheel or
brush with the guard. Wire wheel or brush may expand in
diameter due to work load and centrifugal forces.
Additional safety warnings
Wear safety goggles.
 Use suitable detectors to determine if utility lines are
hidden in the work area or call the local utility company
for assistance. Contact with electric lines can lead to fire
and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage or
may cause an electric shock.
 Release the On/Off switch and set it to the off position
when the power supply is interrupted, e. g., in case of a
power failure or when the mains plug is pulled. This pre-
vents uncontrolled restarting.
 Do not touch grinding and cutting discs before they
have cooled down. The discs can become very hot while
working.
 When working with the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
 Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
 Connect the machine to a mains supply with proper
earthing connection. Socket outlet and extension cable
must be equipped with an operative protective conductor.
Products sold in AUS and NZ only: Use a residual current de-
vice (RCD) with a rated residual current of 30 mA or less.
Safety Warnings for the Power Supply of High-
frequency Tools
 The safety warnings and working instructions of the
frequency converter are to be strictly observed! For de-
tailed information, contact the manufacturer of the fre-
quency converter.
 The frequency converter must be secured with a resid-
ual current protection device when working in an envi-
Bosch Power Tools
ronment where special protection for persons is neces-
sary. The special protection of persons is required, for
example, when working in damp rooms or with materials
that can produce current-conducting dust. Not using a re-
sidual current protection device can lead to electrical
shock, risk of fire, or serious injuries.
 The residual current protection device should be in-
stalled in the power supply network only by a qualified
electrician. Only in this manner can proper functioning be
ensured.
 The output voltage and frequency of the frequency
converter must correspond with the data on the type
plate of the high-frequency tool.
 Operate the power tool exclusively with a fitting plug.
The CEE plug must be dimensioned for the nominal current
that the power tool requires (see "Technical Data").
 Plug mounting and connection to the power supply is to
be carried out by a qualified electrician trained in han-
dling high-frequency tool systems.
 Use only original cables! Before each use, check the
power tool, cable and plug for possible damage. Cables
and plugs may not be repaired, but must be exchanged in
order to avoid danger.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.

Intended Use

Applies for the following types:
– 0 602 301 4..
– 0 602 305 40.
– 0 602 306 434
– 0 602 324 40.
The machine is intended for sanding and polishing metal and
coated surfaces without the use of water.
Applies for the following types:
– 0 602 304 40.
– 0 602 324 44., ... 464, ... 474, ... 434
– 0 602 329 5..
– 0 602 331 5..
– 0 602 332 5..
– 0 602 334 5..
The machine is intended for cutting, roughing and brushing of
metal and stone materials without the use of water.
For cutting with bonded abrasives, a special cutting guide (ac-
cessory) must be used.
When cutting in stone, provide for sufficient dust extraction.
Applies for all types
1 609 92A 36G | (2.11.16)
English | 25