Setting The Timer - THOMSON ROC4507 Manual De Utilización

Setting the Timer

Using the SETUP keys (hold down for 7 seconds), and
5,6,4,3,
navigation keys
display in order to access the stand-by settings for the
TV set and 4 other timers that send sequences of at most
4 keys. Then navigate using keys
Automatic sleep setup for the TV set
Used to program the sleep setup for a TV set using the TV
Sleep Timer mode (" Zzz ").
1. Turn on the device in TV Mode.
2. Using the SETUP keys (hold down for 7 seconds),
and navigation keys
then navigate up to TIMER SETUP
CODE SETUP
(press OK ) then TV SLEEP SETUP (press OK ) then
TV SLEEP SET.
3. Press OK once.
5,6
4. Using keys and OK , select the number
of minutes (from 1 to 90 minutes) before the TV
enters sleep mode when TV SLEEP TIME? is
displayed.
5. The display briefly indicates SUCCESS before
returning to CODE SETUP.
6. Press EXIT twice to exit this mode.
: The " Zzz " symbol is displayed when a TV Sleep Timer
Note
is set.
7. Set the remote control down on a table or flat surface
at the level of the TV set's infrared receiver with its
front end pointed toward the TV set.
Note : to clear the programming, navigate up to TV SLEEp
then TV SLEEp CLEAR . Press OK once when CONFIRM
SETUp
is displayed. The display briefly indicates
OK TO CLEAR
before returning to CODE SETUp.
SUCCESS
Setting the timer
Used to program up to 4 timers. You may assign up to 4
keys to the Timer so that it will activate at the set time (for
example, to change the Mode SAT channel over to 123 at
22:35). The first key must always be a mode key. The
following keys may not include
, or any other mode key. Timers may only
MACRO, SETUP
be set to be activated within the following 24 hour
period. Timers are automatically cleared after having
been activated. The Timer "
a Timer is set.
1. Turn on the device in TV Mode.
2. Using the SETUP keys, and navigation keys
5,6,4,3,
display CODE SETUP then OPTION
OK
then TIMER SETUP (press OK ) then TV SLEEP
SETUP
SETUP then TIMER X SETUP (X corresponds to one of
the 4 timers).
3. Press OK once to display TIMER X SET.
Note : Clear the timer if it already contains a program (see
below).
5,6,
4. Using keys , select the desired start time
OK
(hour and minutes), Press OK .
5. SELECT TIMER X MODE? is displayed. Using the
mode keys, indicate the device to be controlled ( TV,
DVD).
6. The indication SELECT TIMER X KEY? is displayed.
Press once on the key that corresponds to the desired
command (e.g. 1).
7. The indication SELECT KEY 2 is displayed. Press
once on the desired key (e.g. 3) or on OK if you do
only want to send one command, and go to Point 10,
below.
8. The indication SELECT key 3 is displayed. Press once
on the desired key (e.g. 8).
9. The display briefly indicates SUCCESS before
returning to CODE SETUP.
10. Press EXIT to exit this mode.
11. Set the remote control down on a table or flat
surface at the level of the TV set's infrared receiver
with its front end pointed toward the device to be
controlled.
Note: the symbol " " is displayed when a Timer is set.
, go to the TIMER SETUP
OK
5,6,4,3,
.
OK
5,6,4,3,
, display
OK
5,6,4,3,
OK EXIT,
" symbol is displayed when
Clearing a timer
1. Using the SETUP keys (hold down for 7 seconds),
and navigation keys
then OPTION SETUP then TIMER
CODE SETUP
SETUP (press OK ) then TV SLEEP SETUP then
(press OK ) then TIMER X CLEAR.
TIMER X SETUP
2. Press OK once to display TIMER X CLEAR.
3. Press OK once to display CONFIRM OK TO CLEAR.
4. Press OK once.
5. The display briefly indicates SUCCESS before
returning to CODE SETUP.
Key learning
This function is used to copy the functions of keys
on other remote controls to the keys on your ROC
4507 in the mode and to the keys of your choice.
Your ROC 4507 can store up to 150 keys (depending
on the format of the IR code to be learned). Only
one original remote control may be stored per Mode
(refer to the notes concerning learning). The remote
control may also be pre-programmed using one
of the codes in the library, and copied keys may
be «superimposed» on the key positions selected by
the user: The remote control can thus be customised
by the user, who uses a pre-programmed code, then learn
the key functions from his original IR remote control.
: You may not copy onto the Setup, Home Cinema or
Careful
Macro keys • All of the commands copied for one mode are
erased if an identical or new 4-digit code is entered for this
mode (also applies to direct entry of a code, a code search
or brand search) • The screen and key backlighting is off
during learning.
Advice before you begin:
• Place the remote controls face to face so that the
IR LED diodes of the two remote controls are precisely
lined up. You may need to adjust the height of
the remote controls so that the LED diodes are
properly aligned. Verify that the gap between the
two remote controls is about 25 mm [1 inch]. Do not
change the gap between the two remote controls
during the learning of all the keys required for this
mode.
• Begin by copying 2 or 3 keys (to get used to it), then
perform the " Clear All Learn Modes " function (clear
all learn modes) before learning the entire keyboard
of your original remote control.
How to copy (learn) keys
1. Using the SETUP keys (hold down for 7 seconds),
and navigation keys
then navigate up to LEARN SETUP (press OK )
SETUP
then LEARN ONE MODE (press OK ) then SELECT A
MODE KEY.
2. Press OK once.
3. Press the desired mode key once ( TV, DVD, etc.) to
display SELECT A MODE KEY TO LEARN .
4. Press once on the key of your ROC 4507 to which
you wish to copy the code of the original remote
control.
5. The indication LEARNING: PLEASE WAIT appears.
6. While LEARNING: PLEASE WAIT is displayed, hold
down the key on the original remote control until
SUCCESS or KEY LEARN ERROR appears on the
display before releasing the key on the original
remote control (normally after 2-3 seconds).
7. The indication OK – LEARN MORE or EXIT? is
displayed. To copy another key, press once on OK
then begin again starting with Step 5 or press EXIT
once to exit this mode.
8. The display briefly indicates PLEASE WAIT before
leaving this mode.
Erasing the functions learned in a mode
Erases all the keys copied in a given mode
1. Using the SETUP keys, (hold down for 7 seconds)
and navigation keys
then navigate up to LEARN SETUP (press OK )
SETUP
then LEARN ONE MODE then CLEAR ONE LEARN
MODE.
2. Press OK once to display SELECT A MODE KEY.
3. Press the desired key ( TV, DVD, etc.) once to display
CONFIRM OK TO CLEAR
4. Press OK once.
5. The display briefly indicates PLEASE WAIT before
leaving this mode.
5
5,6,4,3,
display
OK
5,6,4,3,
OK , display CODE
5,6,4,3,
, display CODE
OK