Krups ESPRESSERIA AUTOMATIC EA80 Serie Manual De Instrucciones página 19

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 58
Rinsing out the steam circuit:
Place a container under the steam nozzle and press the
which will automatically stop after around 300 ml.
Appliance cleaning program – total duration: about 13 minutes
When a cleaning operation is necessary, the appliance warns you of this by flashing the 'CLEAN' light.
This program is only accessible when the appliance requests it (i.e. approximately every 300 coffees or espressos).
To benefit from the guarantee conditions, it is essential to perform the appliance cleaning cycle when in-
formed to do so. Be sure to follow the procedure closely, step by step.
Only use KRUPS cleaning tablets. You can obtain cleaning tablets from KRUPS Service Centres.
When the indicator light flashes, you can continue to use the appliance but it is recommended that you carry out the
program as soon as possible.
Start the cleaning program by pressing the
and
flash.
Remove, empty and clean the coffee ground collector - Fig. 21.
Replace the coffee grounds collector – Fig. 22
Remove, empty and clean the drip tray - Fig. 23.
Put all parts back in place.
The light
goes out.
Remove, fill and put the water tank back into place.
Place a container with a minimum capacity of 0.6l under the coffee outlets - Fig. 24.
Open the maintenance hatch - Fig. 25 and insert a KRUPS cleaning tablet (XS3000) in the cleaning duct - Fig. 26.
Press the
button to start a cleaning cycle.
The first phase (approximately 10 min) begins. At the end of this phase, the sound signal emits a beep every 10
seconds and you can empty the used water container and the drip tray.
Put the drip tray and container back in place for the next phase.
Press the
button again to start the final phase. The sound signal stops.
Final phase (±3 min)
The program continues. It rinses the appliance and removes any traces of cleaner.
When the cleaning cycle is finished, the indicator light 'CLEAN' goes out.
Remove and empty the used water container.
Empty the drip tray and put back into place.
Refill the water tank.
Your appliance is ready for the next use.
If there is not enough water in the water tank when you start the program, the
the appropriate amount of water to the container and cleaning will continue automatically.
If you unplug the appliance during cleaning, press the
cleaning program will start again from the beginning. In this case, another cleaning tablet may be neces-
sary. Make sure to carry out the full cleaning cycle to ensure good maintenance of your appliance.
The cleaning cycle is intermittent: do not put your hands under the water outlets 'E' and 'W' while the cycle
is in progress.
Only use KRUPS (XS3000) cleaning tablets. We cannot be held responsible for any damage that may result from the
use of tablets from other brands.
You can obtain cleaning tablets from KRUPS Service Centres.
Scale removal program - total duration: about 20 minutes
The quantity of scale deposited depends on the hardness of the water used. The appliance will automatically warn you
by the 'CALC' light coming on when you need to proceed with scale removal.
This program is only accessible when the appliance requests it.
To benefit from the guarantee conditions, it is essential to perform the appliance's scale removal cycle
when informed to do so. Be sure to follow the procedure closely step by step. You can continue to use the appli-
ance when the light is on, but you are advised to perform the program as soon as possible.
button for 3 seconds to start a steam circuit rinsing cycle,
button. The 'CLEAN' light becomes constant and the indicator lights
button, or there is an electrical power cut, the
light will come on to warn you. Add
19

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Espresseria automatic ea81 serieEa80 serieEa81 serieEa8080

Tabla de contenido