Black+Decker FSMH1321 Manual De Usuario página 10

ENGLISH
Using Autoselect , choose from one of the following
TM
applications by turning the Autoselect
required setting is selected.
Setting Mop
Wood/Laminate
Stone/Marble
Tiles/Vinyl
The steam mop will select the correct volume of steam
required for your particular cleaning operation.
Note: Always check you are using the correct setting before
using your steam mop.
Steam Burst (Fig. C1) (only available with units
FSMH1310SM, FSMH13151SM)
The floor head (12a) is equipped with a steam burst pedal to
aid in the removal of stubborn marks and stains.
During use, press the steam burst pedal to apply extra
u
cleaning power.
To revert back to normal setting press the pedal again.
u
Hints for optimum use
General
Caution: Never use the steam mop without first attaching a
cleaning pad.
Always vacuum or sweep the floor before using the steam
u
mop.
The easiest way to use the appliance is to tilt the handle
u
to a 45º angle and clean slowly, covering a small area at a
time.
Use water only with no additives or chemicals with your
u
steam mop. To remove stubborn stains from vinyl or
linoleum floors, you can pre-treat with a mild detergent
and some water before using the steam mop.
Steam Cleaning with the mop
Fit hand held steam cleaner (5) to the steam mop body
u
(11)
Place a cleaning pad (13) on the floor with the velcro 'loop'
u
side facing up.
Lightly press the steam mop down onto the cleaning pad
u
(13).
Connect the steam mop to the mains.
u
Press the ON/OFF button (1). It takes approximately 15
u
seconds for the steam mop to heat up.
10
(Original instructions)
dial (2) until the
TM
Hand held
High temperature steam for
windows

 
Low temperature steam for
heavy grime
  
Turn the Autoselect dial (2) until the required setting is
TM
u
reached. After a few seconds steam will start to come out
of the steam head.
Note! When first filled or after running dry, it can take up to 45
seconds for steam to be produced.
It takes a few seconds for steam to enter the cleaning pad.
u
The steam mop will now glide easily over the surface to be
sanitized/cleaned.
Push and pull the steam mop slowly across the surface to
u
thoroughly steam clean each section.
When you have finished using the steam mop, return
u
the handle (8) to the upright position, making sure that it
is supported and turn it 'OFF'. Wait until the steam mop
cools down (approximately five minutes).
Caution! It is important to monitor the water level in the
water tank. To refill the water tank and continue to sanitize/
clean stand the mop upright making sure that the handle is
supported and turn the steam mop 'OFF'. Unplug the unit from
the electrical wall outlet, and refill the water tank.
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (8) supported in the upright position when
stationary and make sure the steam mop is turned off when
not in use.
Carpet refreshing
Place a cleaning pad (13) on the floor with the 'loop' side
u
facing up.
lightly press the steam mop down onto the cleaning pad.
u
Place the carpet glider (12b) on the floor.
u
Lightly press the steam mop down onto the carpet glider
u
until it clicks into place.
Connect the steam mop to the mains.
u
Press the ON/OFF button (1). It takes approximately 15
u
seconds for the steam mop to heat up.
Turn the Autoselect dial (2) to the Wood/Laminate
TM
u
setting.
Push and pull the steam mop slowly across the carpet to
u
thoroughly refresh each section.
When you have finished using the steam mop, return the
u
handle (8) to the upright position and turn the unit OFF.
Wait until the steam mop cools down (approximately five
minutes).
After use
Turn the Autoselect dial (2) to the OFF position.
TM
u
Wait until the steam mop cools down.
u
Unplug the steam mop from the electrical wall outlet.
u
Empty the water tank.
u
remove the cleaning pad (13) and wash it ready for next
u
use (take care to follow the wash care instructions printed
on the cleaning pad).