Technische Daten - Trixie TX8 Smart Instrucciones De Uso

Technische Daten

Modell: TX8 Smart
Fassungsvermögen: 4,3 Liter
Frequenzband: 2.4 – 2.48 GHz
Sendeleistung: ≤20 dBm (EIRP)
WiFi-Standard: 802.11 b/g/n/
Stromversorgung: Netzteil, DC 5 V; 2 A
Netzteil: Modell: AS1201A-0502000EUL
Nennspannung: 100-240 V ~, 50/60 Hz; 0,35 A MAX
Ausgangsspannung: 5 V, 2000 mA
Abmessungen (B × H × T): 24 × 38 × 19 cm
Gewicht: ca. 1,3 kg
Bei Fragen zu Ihrem Smart-Gerät kontaktieren Sie bitte den
Support: smartsupport@trixie.de
Die Bedienung dieses Gerätes erfolgt mit Hilfe der in den App Stores
kostenlos verfügbaren App „Tuya Smart" der Tuya Inc.
Bitte beachten Sie die dort genannten Nutzungsbedingungen und
Datenschutzhinweise.
E Instructions
• Read the operating instructions before use.
• The pet feeder is not a toy for children. Do not let children play with
the packaging foil. Danger of suffocation!
• The feeder is only suitable for dry food (diameter 5 - 15 mm).
• Do not use it with puppies and kittens under 7 months.
• The base unit must not get wet - not dishwasher suitable.
• Additional instructions for the use of IOT devices can be found at the
end of this manual.
Electric Shock Hazard!
• Incorrect use may result in electric shock.
• The mains voltage of the socket must match the specification on the
automatic feeder.
• Ideally, use an easily accessible socket so that you can quickly dis-
connect the feeder from the mains if necessary.
• Do not use the feeder if there is visible damage to the appliance or
the mains cable or plug.
• Do not open the feeder, but contact our customer service.
• Do not use a timer or other remote control system.
• Never touch the mains plug with wet hands.
Safety
• The feeder is suitable for indoor use only.
• Place the feeder on a level surface. The feeder must be sufficiently
ventilated on the sides.
• Only use the feeder with the feed container and lid, and do not place
anything on top of it.
• Never pull the mains plug out of the socket by the cable, always
grasp the mains plug.
• Do not use the power cord as a carrying handle.
• Keep the feeder and power plug away from open flames and heat.
• Route the power cord so that it does not become a tripping hazard.
• Do not kink the power cord or place it over sharp edges.
• Do not allow your pet to nibble on the feeder or cord. If necessary,
protect it with a cord protector.
• Never reach for an electrical appliance if it has fallen into the water.
In such a case, unplug the appliance immediately.
• Unplug the feeder when not in use or when cleaning it.
Preparation
1. Connect the feeder to a power source using the power plug. Turn on
the main switch on the bottom.
2. To control and program the feeder, download the „Tuya Smart" app
to your mobile phone or tablet. By scanning the QR code, you will be
taken directly to the download:
3. Optionally, you can insert 3 x D Mono batteries into the device as an
emergency power supply. The programmed feeding times can thus
be guaranteed even in the event of a power failure. Please note that
the feeder is not accessible via the app in emergency mode.
How to Register
Open the app and click on REGISTER to create an account.
Coupling the Device
In the next step, the automatic feed dispenser is connected to the
internet and coupled to your smartphone. Please be sure to follow
the following instructions to ensure trouble-free connection:
• The automatic feed dispenser should be place near (max. distance
3 m) your WLAN router while the connection is established. At the
same time, your smartphone should be quite close (max. distance
1 m) to the feed dispenser.
• Ensure that your smartphone is connected to the WLAN and has a
high signal level.
• Please note that coupling the automatic feed dispenser only works
at the frequency of 2.4 GHz. If you have a WLAN router that sends
out 2.4 GHz as well as 5 GHz, you have to make sure you choose
the right frequency band.
• There are two options for coupling the device: EZ mode and AP mode.
Some dual-band routers use a joint SSID (name of the network) for both
frequencies. If that is the case, the coupling in EZ mode will only work if
your first separate both frequency bands in the settings of your router
and assign a separate SSID for both frequencies. As an alternative, you
can also deactivate the 5 GHz temporarily. Check in the manual of your
router if you are not sure what type of router you have or how you can
change these settings. The AP mode described further down offers ano-
ther option how to solve the problem. This coupling mode works with
dual band routers without prior separation of both frequencies.
• Please note that the feeder will not work in 5.0 GHz-only networks.
• If your Wi-Fi password contains special characters, you may expe-
rience problems during the pairing process. Change your wireless
password to contain only letters and numbers.
AP Mode (Recommended)
1. Press the SET button at the top of the device 11 times quickly to
activate AP mode. An acoustic signal confirms the activation, and a
green indicator light should begin to flash slowly after a few seconds.
2. In the app, select ADD DEVICE and then select SMART CAMERA
under SECURITY & VIDEO SURVEILLANCE (Wi-Fi).
5