Ce Conformity Declaration; Disposal Notes - Multiplex MULTIcont BL-17 Manual De Instrucciones

BL-17 / BL-17/II / BL-27/II / BL-37/II / BL-54 brushless controllers
8. L -
OW VOLTAGE CUT
FUNCTION
If the battery voltage falls to the low-voltage threshold, the
controller automatically cuts off power to the motor. This
ensures that sufficient energy is available for the BEC
power supply to allow a safe landing to be carried out. A
steady decline in motor speed is a further indication that
the flight battery is almost discharged; you should initiate
the landing as soon as you become aware of this.
If the controller cuts the motor, it can be switched on again
briefly if required by momentarily moving the throttle stick
to the motor OFF position (Reset function).
! Note: do not use the low-voltage reset function
more than once or twice
Repeated throttling back to re-arm the motor may dis-
charge the flight battery to the point where the receiver
power supply falters and fails. Note that LiPo flight
batteries can be permanently damaged if they are deep-
discharged.
9. F -
AULT FINDING
The controller switches the motor off after a few
seconds
The controller will switch the motor off immediately if the
battery voltage falls below the low-voltage threshold. This
is designed to prevent loss of control of the model due to
low voltage at the receiver. If the battery is fully charged
and you apply full-throttle, a motor cut indicates a serious
voltage collapse in the flight battery. Measure the current
drain, and either install a smaller propeller or fit a battery
with a higher current delivery capacity (higher C-rate).
Serious interference or failure of the transmitter signal will
also cause the controller to cut the motor immediately.
Throttle the motor back, wait about one second, then re-
arm the controller by opening the throttle again; this will
only work if proper reception has been restored.
Everything is connected correctly, the BEC system is
working, the servos are operating, but the throttle
function does not work
You probably did not wait long enough in the motor OFF
position after connecting the flight battery; this means that
the controller is not armed. Move the stick back to the
motor OFF position (trim also at idle end-point) and wait
one or two seconds. Check that the throttle channel is set
to full travel, i.e. at least 100%. If the two rising beep
sequences still do not sound, and the motor still does not
start, you need to reverse the direction of operation of the
throttle channel at the transmitter.
Nothing works: receiver, servos and controller do not
function at all
Check all plugs, sockets and solder joints for intermittent
contact, and check again for correct polarity (+/-). If the
unit still does not work, contact the dealer from whom you
purchased the speed controller.
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten (Gölshausen) • www.multiplex-rc.de
Operating Instructions MULTIcont
-
OFF WITH RESET
,
FAULT CORRECTION
10. G / L
UARANTEE
Our products are covered by the currently valid statutory
guarantee regulations. If you wish to make a claim under
guarantee, please contact the model shop where you
originally purchased the unit.
The guarantee does not cover faults caused by:
• Incorrect handling, incorrect connections, reversed po-
larity
• The use of accessories other than original MULTIPLEX
items
• Modifications or repairs not carried out by MULTIPLEX
or by an authorised MULTIPLEX Service Centre
• Accidental or deliberate damage
• Normal wear and tear
• Use of the unit outside the stated Specification
MULTIPLEX Modellsport GmbH & Co.KG accepts no
liability for loss, damage or costs which are caused by the
incorrect or incompetent use of the product, or are con-
nected with such use in any way.
11. CE C
ONFORMITY
This device has been assessed in accordance with
the relevant harmonised European directives.
You are therefore the owner of a product whose design
fulfils the protective aims of the European Community
relating to the safe operation of equipment.
You are entitled to see the conformity declaration. Please
ask MULTIPLEX Modellsport GmbH & Co.KG for a copy.
12. D N
ISPOSAL OTES
Electrical equipment marked with the cancelled
waste bin symbol must not be discarded in the
standard household waste; instead it must be ta-
ken to a suitable specialist disposal or recycling
system.
In the countries of the EU (European Union), electrical
equipment must not be discarded via the normal domestic
refuse system (WEEE - Waste of Electrical and Electronic
Equipment, Directive 2002/96/EG). You can take un-
wanted equipment to your nearest local authority waste
collection point or recycling centre, where the staff will dis-
pose of it correctly and at no cost to yourself.
By returning your unwanted equipment you can make an
important contribution to the protection of our shared
environment!
E
IABILITY XCLUSION
D
ECLARATION
Page 4/4