Casals CAG13/125VCEK Manual De Usuario página 7

e ap- from the effect of its own mechanical inertia.
- Always wait until the machine has come to a complete
iately stop before placing it down. The tool insert can jam and
nt the lead to loss of control over the power tool.- Fully unroll
the appliance's power cable before each use.
floor, - Check the position of power cables before commenc- Check the position of power cables before commenc-
eak. ing work ensuring they are well away from the work
area.
et, or - Keep hands and other body parts well away from the
work area whist the tool is in use.
ce. - Keep hands and other body parts well away from the
discs while the angle grinder is in use. Do not attempt
r tan- to remove cut material whilst the angle grinder is in op-
eration or reach underneath for any reason.
- Do not use the appliance if the parts or accessories
nger- are not properly fitted.- Do not use the appliance if the
ignite accessories or consumables attached to it are defec-
tive. Replace them immediately.
with - Use the appliance handle/s, to catch it or move it.
e than - Unplug the appliance from the mains before replacing
any accessory.
at the - Unplug the appliance from the mains when not in use
ch or and before undertaking any cleaning task.
hold it - This appliance is for professional use.
ance. - This appliance is intended for adult use. Ensure that
ands. this product is not used by the disabled, children or
speed people unused to its handling.
e ap- - This appliance is not a toy. Children should be super-
vised to ensure that they do not play with the appliance.
ol di- - Take special care about discs and tools, they may be
stored fixed on the appliance and used according to the
/ tool manufacturer's instructions.
- Do not use separator or reducing bushings, adapters
speed to fix the discs / tools they are not directly compatible
with the appliance.
when - Do not use cutting discs on deburring operations.
it has - Do not expose to extreme temperatures or strong
r tool magnetism.
- Keep the appliance in a dry, dust-free place, out of
when direct sunlight.
kback - Always check the workpiece before operation and re- Always check the workpiece before operation and re-
move any obstructions such as nails, staples, screws,
parts string, rags, cloths and other debris.
- Before cutting ensure there is a suitable gap below
Work- the workpiece to prevent the disc from touching any
pro- obstacles.
these - Only use the appliance for carrying out dry tasks.
h and - Never rest the appliance into a surface while in use.
- Do not use the appliance on any part of the body of
he bit a person or animal.
- Let the appliance running with no load for 30 sec-
pera- onds in a safe position. If you notice serious vibration
oving or other defects stop the appliance immediately. Then
check the problem and /or proceed as we describe on
Anomalies and Repair clause.
Product description and Specifications
Description:
A Start-up switch
B Auxiliary handle
C Disc protector
D. Ventilation openings
E Spindle blocking button
F Spindle
H Support plate
I Disc (not included)
J Clamping nut
K Tightening key
L Collard of guard
M Bolt
N Lever
O Speed regulator control
Instructions for use
Before use:
- Make sure that all the product's packaging has been
removed.
- Before connecting the power cord to the mains power
supply ensure the switch is in the off position.
- Ensure the auxiliary handle is fitted correctly before
use.
- Prepare the appliance according to the function you
wish to use:
Fitting safety devices
Fitting the disc guard (Fig.5)
- Never use the machine without guard. Keep guards
in place.
- The guard should be positioned so the closed side of
the guard points towards the operator.
- Unplug the appliance from the mains.
- Fit the collar of the guard (L) on the flange of the ap-
pliance.
- If the guard doesn't fit in the flange, loosen the bolt
(M).
- Turn the guard to the desired working position.
– To fasten the protection guard close the lever (N)
Fitting the auxiliary handle
- Unplug the appliance from the mains.
Use of the auxiliary handle is obligatory in order to
7