Reset Keypad; Reset Master Code - position C2RLC Manual De Instalación

INSTALLATION MANUAL
C2RLC - C2RLCE
Stainless Steel Keypads - Self contained
6] PROGRAMMATION
Description:
- Input voltage 12V dc.
- 12 digits fluorescent keys keypad.
- Stored in non-volatile
EPROM memory.
- Capacity of 100 user codes
programmable in 4, 5 or 6 digits.
- 2 relay outputs N/O and N/C
contacts 5A / 250V~.
- Master code programmable
in 4, 5 or 6 digits.
- Buzzer audible signal.
- 1 request-to-exit input.
- Master code factory default value
and reset of all the user codes.
Default Values:
- No user code.
- Relay release time : 1 s.
- Code length: 5-digits.
- Master code: 1 2 3 4 5.
- Programming Security time: 120 s.
- One beep when keypad powered
(green LED ON).
- Panic function: Off.
A. Reset Keypad
1. Cut the power of the keypad (Green
LED lights OFF): Short the RAZ.
2. Put the power back (Green LED lights ON):
- After a few seconds, a beep is emitted.
- Remove the shortage on RAZ terminals.
3. The master code is restored to its default
value 1 2 3 4 5 and all the User codes
are deleted from the keypad.
B. Reset Master Code
1. On standby mode Green LED ON:
- Short RAZ terminals
- The red LED lights ON.
2. Wait until the red LED lights OFF:
- 1 beep is emitted.
- Remove the short on the RAZ terminals.
3. The master code is restored to the factory
default value 1 2 3 4 5.
4
position.eu.com
- Security level: After 4 invalid user
codes, keypad is locked out during
30 seconds.
- Audible feedback from keypad
keys: OFF
Audible signal:
- 1 short beep:
keypad powered,
- 1 long beep: Data computing
in programming
and access granted,
- 2 short beeps: Entry or Exit
from programming,
- 4 short beeps:
Data computing error.
Code length:
- The master code and the User
codes can be of 4 to 6-digits
in length.
- All the keypad keys can be
used to program a code.
- The master code and the Pin
code can be of 4 to 6-digit code.
C. Setting the Code Length
1. Enter the master code twice.
(1 2 3 4 5 default value master code).
- 2 beeps are emitted to confirm entry in
2. Press
- One beep is emitted.
- Press 4, 5 or 6 for the number of digits
- One beep is emitted to confirm programming
3. Press
- One beep is emitted.
- Enter the new master code in 4, 5 or 6 digits.
- One beep is emitted to confirm programming
4. Press # to exit from the programming mode:
2 beeps are emitted to confirm that the keypad
is in stand-by operating mode.
- The master code CAN NOT be used
as a PIN code (User Pin code).
- To delete a specific User pin Code
replace it by 0 0 0 0 if code
length is 4-digits format or
replace it by 0 0 0 0 0 if the
code is in 5-digits format or if
the code is 6-digits format
then put 0 0 0 0 0 0.
Request-To-Exit Input:
P1 input activate relay 1
(the output is programmable).
Consumption:
when 2 relay outputs are
activated and the keypad keys
are illuminated in 12V dc:
Maximum 120mA.
LED's:
- Green LED: Power ON,
- Red LED: Relay 1 activated,
- Orange LED: Relay 2 activated.
programming mode (the Orange LED lights ON).
* 3 to program the code length:
of the code length.
* 4 to modify the master code:
of the new master code.
4 beeps indicate
a data computing error
EN