Bolt Torque Chart - Woods PREMIER PRD6000E Manual Del Operador

Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific
application.
Fasteners must always be replaced with the same grade as specified in the manual parts list.
Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware.
Make sure fastener threads are clean and you start thread engagement properly.
All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 & J1701M JUL 96.
SAE SERIES
TORQUE
A
CHART
A
Diameter Wrench
(Inches) Size
1/4" 7/16"
5/16" 1/2"
3/8" 9/16"
7/16" 5/8"
1/2" 3/4"
9/16" 13/16"
5/8" 15/16"
3/4" 1-1/8"
7/8" 1-5/16"
1" 1-1/2"
METRIC SERIES
TORQUE
A
CHART
A
Diameter &
Thread Pitch Wrench
(Millimeters) Size
6 x 1.0 10 mm
8 x 1.25 13 mm
10 x 1.5 16 mm
12 x 1.75 18 mm
14 x 2.0 21 mm
16 x 2.0 24 mm
18 x 2.5 27 mm
20 x 2.5 30 mm
22 x 2.5 34 mm
24 x 3.0 36 mm
30 x 3.0 46 mm
Typical Washer Installations
Bolt
34 Appendix

BOLT TORQUE CHART

SAE Bolt Head
SAE Grade 2
(No Dashes)
SAE 2
lbs-ft N-m
6 8
12 17
23 31
36 48
55 75
78 106
110 149
192 261
306 416
467 634
8.8
Metric
Grade 8.8
COARSE THREAD
MARKING ON HEAD
Metric 8.8 Metric 10.9
N-m lbs-ft N-m
8 6 11
20 15 27
39 29 54
68 50 94
109 80 151
169 125 234
234 172 323
330 244 457
451 332 623
571 421 790
1175 867 1626
Flat Washer
Lock Washer
Identification
SAE Grade 5
(3 Radial Dashes)
MARKING ON HEAD
SAE 5
lbs-ft
10
19
35
55
85
121
170
297
474
722
Metric Bolt Head
Identification
FINE THREAD
MARKING ON HEAD
Metric 8.8
lbs-ft N-m lbs-ft
8 8
20 21
40 41
70 75
111 118
173 181 133
239 263 194
337 367 270
460 495 365
583 623 459
1199 1258 928
Bolt Torque & Size Charts (Rev. 3/28/2007)
SAE Grade 8
(6 Radial Dashes)
SAE 8
N-m lbs-ft
13 14
26 27
47 49
75 78
115 120
164 171
230 240
403 420
642 669
979 1020
10.9
Metric
Grade 10.9
Metric 10.9
N-m lbs-ft
6 11 8
16 29 22
30 57 42
55 103 76
87 163 120
250 184
363 268
507 374
684 505
861 635
1740 1283
N-m
18
37
67
106
163
232
325
569
907
1383
A
Diameter &
Thread Pitch
(Millimeters)
6 x 1.0
8 x 1.0
10 x 1.25
12 x 1.25
14 x 1.5
16 x 1.5
18 x 1.5
20 x 1.5
22 x 1.5
24 x 2.0
30 x 2.0
Hn cv" Y