Final Installation Checklist; Operation Checklist - GE Cafe CT9570SLSS Instrucciones De Instalación

13
DOOR ADJUSTMENT MECHANISM
Door Adjustment Mechanism is located on both the right and left doors at the bottom hinges. Only
the left side Adjustment Mechanism is shown in this manual.
NOTE: Adjust the doors inward only until the center gap is even. Over-adjusting can damage the
center seals and make the doors more difficult to open.
A. Using 3/16" hex key, tighten Vertical Adjustment Screw to adjust door up and loosen to adjust
door down.
Horizontal Adjustment Screws
B. Horizontal Adjustment Screws pivot
the door about an axis. Using a 1/8"
Hex Key, loosen both screws, then
tighten appropriate screw to pivot
door. Once door is in place, verify
both screws are tightened.
EXAGGERATED EXAMPLES FOR
LEFT DOOR ADJUSTMENT
Example 1: Left door low, Example 2: Left door low,
center gap even. center gap larger at bottom.
Steps for adjustment: Steps for adjustment:
A. Tighten left Vertical A. Loosen inside Horizontal
Adjustment Screw. Adjustment Screw.
B. If left door is still low, loosen B. Tighten outside Horizontal
right Vertical Adjustment Adjustment Screw until
Screw. center gap even.
C. If left door is still low, tighten
left Vertical Adjustment
Screw.
D. Tighten inside Horizontal
Adjustment Screw.
Vertical Adjustment Screw
Example 3: Left door high,
center gap larger at top.
Steps for adjustment:
A. Loosen outside Horizontal
Adjustment Screw.
B. Tighten Outside Horizontal
Adjustment Screw until
center gap even.
C. If left door is still low, tighten
Left Vertical Adjustment
Screw.
D. Tighten Inside Horizontal
Adjustment Screw.
14
REPLACING THE LOWER OVEN DOOR
NOTE: The oven door is heavy. You may need help lifting the door high
enough to slide it into the hinge slots. Do not lift the door by the handle.
A. Lift the oven door by grasping each side.
B. With the door at the same angle as the removal position (approximately
1"–2" [2.5 cm–5.1 cm] from the closed position), seat the notch of the
hinge arm into the bottom edge of the hinge slot. The notch of the
hinge arm must be fully seated into the bottom of the slot.
C. Fully open the door. If the door will not fully open, the indentation is not
seated correctly in the bottom edge of the slot.
D. Push the hinge locks up against the front frame of the oven cavity,
to the locked position.
E. Replace hinge bracket, if equipped, to ensure proper door functionality.
F. Close the oven door.
Bottom
Hinge in
Edge of
Locked
Slot
Position
Notch of Hinge
Securely Fitted
Into Bottom of
Hinge Slot
15

FINAL INSTALLATION CHECKLIST

• Check to make sure the circuit breaker is closed (RESET) or the circuit fuses are replaced.
• Be sure power is in service to the building.
• Check that all packing material and tape have been removed. Failure to remove these materials
could result in damage to the appliance once the appliance has been turned on and surfaces
have heated.
• Remove all items from inside the oven.
• Check to be sure that the mounting screws are installed and flush with the side trim
(see Section 10).
• Check that the bottom trim is installed properly (see Section 11).
• Ensure that air duct opening at bottom of unit is free of obstructions.
• Check that oven rack guides are installed correctly and oven racks function smoothly.

OPERATION CHECKLIST

• Turn on the power to the oven (refer to your Owner's Manual). Verify that the bake and broil
units and all cooking functions operate properly.
• See your Owner's Manual for the troubleshooting list.
• Be sure all of the oven controls are OFF before leaving the oven.
Hinge Bracket
Hinge
Arm
Hinge Notch