Using The Remote Control - DeLonghi TCH7915ER Manual De Instrucciones

voltage shown on the appliance rating label and the outlet
you are going to use is in good condition.
Operation and use
- Connect the appliance to the power outlet.
- The appliance emits a beep and the power indicator
light (H) comes on and remains on as long as the
appliance is powered.
- The appliance goes into OFF. If the display shows a
blinking dot, it means that the tip over switch has been
activated. See paragraph: "Additional safety features".
- Press the ON/OFF button (A) to turn on the appliance. It
will begin to heat with the predefined settings.
MODE button
Press the MODE button (F) to select one of the following
functions available:
Ventilation
-
In this operating mode only the fan operates, so the
appliance does not heat the room.
Anti-freeze
-
In this operating mode the appliance keeps the room
at a temperature of 45°F (7°C) to prevent freezing
temperatures.
- Heating 1 and Heating 2
In this operating mode you can set the desired
temperature by pressing the + and - adjustment
buttons (B).
Heating 1 (minimum power level):
l
The appliance operates at the minimum power, reducing
noise and energy consumption to the minimum.
Heating 2/BOOST function (maximum power
l
level):
The appliance operates at the maximum power for rapid
heating of the room.
ECO function
In this operating mode the appliance will automatically set
the power level to guarantee the best comfort reducing the
energy consumption. In this operating mode the unit may
switch the heating power level from maximum to minimum
and viceversa, several times in an hour.
When using the ECO function, the maximum temperature
setting is 79°F (26°C). To activate this function, press the ECO
button (D):
- If you want the appliance to distribute the airflow over
a larger area, press the oscillation button (C)
appliance will then oscillate right and left. To stop the
oscillation in the desired position, just press oscillation
button (C) again.
- To turn off the appliance press button ON/OFF (A). The
display will show a count down for about 6 seconds.
Please note: The display can show the temperature in
both °F and °C. To change the temperature scale, press and
hold the + key for around 8 seconds, then release.
Please be informed that as this is not a precision device, the
showed temperature not necessary corresponds to the real
one.
24 h digital timer
This function can be activated from any operating mode.
Delayed switch-on: with the appliance in the OFF position,
press the timer button (E )
and the time remaining before switch-on. To set the
timer, use the + and - adjustment buttons (B), then wait a
few seconds for the programming to be set.
The display shows the symbol
the timer. When the programmed time has been reached, the
appliance turns on with the same settings it had during the
previous operation.
Auto-off: with the appliance on, press the timer button
(E) . The display shows the symbol
remaining before shut-off. To set the timer, use the + and
- adjustment buttons (B), then wait a few seconds for the
programming to be set. The display returns to show the
current settings and the symbol
the timer. When the programmed time as been reached the
appliance shuts off automatically. If you want to go back to
operation without the timer, press the timer button (E) twice.
The timer symbol

Using the remote control

The remote control functions correspond to those on the
control panel. See the section "Operation and Use" on the
previous page for a description of the functions.
Important! This product contains a button battery.
If swallowed, it could cause severe injury or death in just 2
hours. Seek medical attention immediately.
Inserting or replacing the batteries
- The remote control is provided with a lithium battery
CR2032. To let the appliance function, remove the
battery cover strip, by pulling it.
. The - To replace the batteries, remove the battery cover by
rotating it. Replace the battery paying attention to
respect the right polarity as shown in figure 2.
6
. The display shows the symbol
to indicate you have set
and the time
to indicate you have set
disappears from the display.