Tabla de contenido
Publicidad
Enlaces rápidos
E
Operator's Manual
Manuel d'utilisation
Libro de Instrucciones
READ THIS BOOK
This book has important information for the use and safe operation of this machine. Failure to read
this book prior to operating or attempting any service or maintenance procedure to your ALTO
machine could result in injury to you or to other personnel; damage to the machine or to other property
could occur as well. You must have training in the operation of this machine before using it. If you
cannot read English, have this manual explained fully before attempting to operate this machine.
All directions given in this book are as seen from the operator's position at the rear of the machine.
For new books write to: ALTO U. S. Inc., 2100 Highway 265, Springdale, Arkansas 72764
Form No. 79002B
6/01
CLARKE TECHNOLOGY
FUSION
20I/20IX
Printed in the U.S.A.
Publicidad
Tabla de contenido
Manuales relacionados para Clarke Technology ALTO FUSION 20I
Resumen de contenidos para Clarke Technology ALTO FUSION 20I
- Página 1 All directions given in this book are as seen from the operator’s position at the rear of the machine. For new books write to: ALTO U. S. Inc., 2100 Highway 265, Springdale, Arkansas 72764 Form No. 79002B 6/01 CLARKE TECHNOLOGY Printed in the U.S.A.
-
Página 2: Tabla De Contenido
36 Volt Battery Charger ........................ 54 Fusion 20 I Electrical Schematic ....................55 Fusion 20 IX Electrical Schematic ....................56 Fusion 20 IX Connection Diagrams ....................57 Fusion 20I Connection Diagrams ....................58 Page CLARKE TECHNOLOGY Operator's Manual -Fusion 20 Burnisher... - Página 3 Diagrama eléctrico del modelo Fusion 20I ................... 55 Diagrama eléctrico del modelo Fusion 20IX ..................56 Diagrama de las conexiones modelo Fusion 20I .................. 57 Diagrama de las conexiones modelo Fusion 20IX ................58 CLARKE TECHNOLOGY Operator's Manual - Fusion 20 Burnisher...
- Página 4 Schéma électrique du modèle Fusion 20I ....................55 Schéma électrique du modèle Fusion 20IX ..................... 56 Diagramme des connexions modèle Fusion 20I ..................57 Diagramme des connexions modèle Fusion 20IX ..................58 Page CLARKE TECHNOLOGY Operator's Manual -Fusion 20 Burnisher...
-
Página 5: Operator Safety Instructions
Failure to read the Owner's Manual prior to operating or attempting any service or maintenance procedure to your Clarke Technology machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. - Página 6 Do not use this machine as a step or furniture. Do not ride on this machine. CAUTION: Your machine warranty will be voided if anything other than genuine Clarke Technology parts are used on your machine. Always use Clarke Technology parts for replacement.
-
Página 7: Instrucciones De Seguridad Para El Operador
La máquina puede volcar si está en posición inestable sobre una escalera o una rampa de carga y causar lesiones o daños materiales. Pare la máquina sólo en una superficie plana. Al parar la máquina, compruebe que la llave del interruptor principal está en la posición ‘O’. CLARKE TECHNOLOGY Operator's Manual - Fusion 20 Burnisher... - Página 8 ¡AVISO! Sólo el personal cualificado y autorizado por Clarke Technology puede efectuar el mantenimiento y las reparaciones de nuestras máquinas. ¡ Se trata de su seguridad ! ¡ AVISO ! El agua o la humedad pueden causar cortocircuitos en el sistema eléctrico. Procure que el sistema eléctrico sea siempre seco.
- Página 9 N’utilisez jamais un chargeur dont le câble d’alimentation est endommagé. !AVERTISSEMENT!: La seule position correcte pour l’opérateur est debout, derrière la machine. Toute autre position de conduite risque de provoquer des blessures ou des dégâts. CLARKE TECHNOLOGY Operator's Manual - Fusion 20 Burnisher...
- Página 10 à clé sur “O”. !AVERTISSEMENT!: Seul un personnel qualifié, agréé par Clarke Technology, a le droit d’effectuer les réparations et l’entretien de nos machines. Il y va de votre sécurité! !AVERTISSEMENT!: L’eau ou l’humidité...
-
Página 11: Introduction & Machine Specifications
Introduction & Machine Specifications Introduction & Machine Specifications Clarke Technology’s newly designed Fusion 20 I and 20 IX burnishers are efficient and superior floor burnishing machines. The Fusion 20 uses one pad to burnish a path 20 inches wide. The powder created by burnishing is collected by a dust control system in the pad housing. -
Página 12: Introduccion Y Caracteristicas Tecnicas
INTRODUCCION Y CARACTERISTICAS TECNICAS Introducción Los últimos modelos de pulidoras CLARKE TECHNOLOGY, la Fusion 20I y la Fusión 20IX, procuran un rendimiento superior para el mantenimiento del suelo. La Fusion 20 tiene un disco de 51 cm de anchura. El polvo debido al pulido es recogido por un dispositivo especial que se encuentra en la tapa de protección del... - Página 13 INTRODUCTION ET CARACTERISTIQUES TECHNIQUES Introduction Les derniers modèles de polisseuses CLARKE TECHNOLOGY, la Fusion 20I et la Fusion 20IX offrent un rendement supérieur pour l’entretien des sols. La Fusion 20 est équipée d’un disque de 51 cm de diamètre. La poussière qui se forme lors du polissage est récoltée grâce à...
-
Página 14: Procedures For Transporting 20 Ix
4. Put the ramp in position. 5. Unfasten the machine. Figure 3 WARNING: The machine is heavy. Make sure you use two able persons to assist in moving the machine down the ramp. Page -14- CLARKE TECHNOLOGY Operator's Manual -Fusion 20 Burnisher... -
Página 15: Procedimiento Para El Transporte
¡ AVISO ! : La máquina pesa. Se necesitan ! AVERTISSEMENT ! : La machine est lourde. dos personas para manejarla Il faut deux personnes sobre la rampa. pour la manoeuvrer sur la rampe. CLARKE TECHNOLOGY Operator's Manual - Fusion 20 Burnisher... -
Página 16: Procedures For Transporting 20 I
10. Lorsque la machine commence à descendre la rampa, pulse uno de los interruptores marcha rampe, enfoncez un des interrupteurs marche adelante / atrás para controlar la velocidad. avant/arrière pour contrôler la vitesse. Page -16- CLARKE TECHNOLOGY Operator's Manual -Fusion 20 Burnisher... -
Página 17: Symbols Used On Fusion 20 I And 20Ix
USE ONLY COMMERCIALLY AVAILABLE FLOOR CLEANERS AND WAXES INTENDED FOR MACHINE OPERATION. Battery Meter DO NOT USE FLAMMABLE MATERIALS. DO NOT TURN, STOP, OR LEAVE MACHINE ON A RAMP OR DOCK. 77261A CLARKE TECHNOLOGY Operator's Manual - Fusion 20 Burnisher... -
Página 18: Simbolos Utilizados Con La Fusion 20I Y 20Ix
AVAILABLE FLOOR CLEANERS Indicador de cargo de las AND WAXES INTENDED FOR MACHINE OPERATION. baterías DO NOT USE FLAMMABLE MATERIALS. DO NOT TURN, STOP, OR LEAVE MACHINE ON A RAMP OR DOCK. 77261A Page -18- CLARKE TECHNOLOGY Operator's Manual -Fusion 20 Burnisher... - Página 19 AVAILABLE FLOOR CLEANERS AND WAXES INTENDED FOR MACHINE OPERATION. Indicateur de charge des DO NOT USE FLAMMABLE MATERIALS. batteries DO NOT TURN, STOP, OR LEAVE MACHINE ON A RAMP OR DOCK. 77261A CLARKE TECHNOLOGY Operator's Manual - Fusion 20 Burnisher...
-
Página 20: Machine Control Panel Fusion 20 I
The hour meter indicates the number of hours of the machine has operated. It runs only when the pad CAUTION: Do not activate the brake motor is running. while the machine is moving. Figure 9 Figure 10A Figure 10B Page -20- CLARKE TECHNOLOGY Operator's Manual -Fusion 20 Burnisher... - Página 21 ; para aflojar el freno, levante el pedal (figura 10b). !ATTENTION!: Ne pas engager le frein de ¡ CUIDADO ! No meta el freno de stationnement lorsque la estacionamiento cuando la machine est en mouvement. máquina está en movimiento CLARKE TECHNOLOGY Operator's Manual - Fusion 20 Burnisher...
-
Página 22: Machine Control Panel Fusion 20 Ix
CAUTION: Do not activate the brake while the machine is moving. Figure 9 Figure 10A Figure 10B Page -22- CLARKE TECHNOLOGY Operator's Manual -Fusion 20 Burnisher... - Página 23 (figure 12b). ¡ CUIDADO ! No meta el freno de estacionamiento cuando la !ATTENTION!: Ne pas engager le frein de máquina está en movimiento. stationnement lorsque la machine est en mouvement. CLARKE TECHNOLOGY Operator's Manual - Fusion 20 Burnisher...
-
Página 24: How To Prepare The Machine For Operation
8. Join the connector from the battery pack to the connector on the control panel. See Avant de la machine figure 14. Figure 13B 9. Reassemble machine. NOTE: Charge the batteries before using the machine. Figure 14 Page -24- CLARKE TECHNOLOGY Operator's Manual -Fusion 20 Burnisher... -
Página 25: Preparacion De La Maquina Para Trabajar
8. Reliez le connecteur du groupe des batteries au NOTA : Cargue las baterías antes de utilizar la connecteur du tableau de commandes. Voir máquina. figure 14. 9. Réassemblez la machine. REMARQUE : Chargez les batteries avant d’utiliser la machine. CLARKE TECHNOLOGY Operator's Manual - Fusion 20 Burnisher... -
Página 26: Battery Maintenance
To clean the terminals and connectors, use a terminal and connector cleaning tool. Do not allow ammonia or bicarbonate of soda to get into batteries. Keep the batteries charged. Page -26- CLARKE TECHNOLOGY Operator's Manual -Fusion 20 Burnisher... - Página 27 Procure que la solución de amoníaco o de bicarbonato de sosa no penetra dentro de las 3. Veillez à ce que les batteries soient toujours baterías. chargées. 3. Procure que las baterías siempre sean cargadas. CLARKE TECHNOLOGY Operator's Manual - Fusion 20 Burnisher...
-
Página 28: How To Charge The Batteries
(3-wire) wall receptacle having the voltage, frequency, and ampere capacity specified on the nameplate of the charger. For more instruction on the use of the charger, read the instruction book supplied with the charger. Figure 18 Page -28- CLARKE TECHNOLOGY Operator's Manual -Fusion 20 Burnisher... - Página 29 Des instructions complémentaires concernant l’utilisation du chargeur figurent dans le livret d’instruction fourni avec celui-ci. CLARKE TECHNOLOGY Operator's Manual - Fusion 20 Burnisher...
-
Página 30: How To Install The Pad
7. Retighten the pad retainer as tight as possible. Figure 20 8. Raise the back of the machine to lower the pad housing by lifting as shown in figure 21. Figure 21 Page -30- CLARKE TECHNOLOGY Operator's Manual -Fusion 20 Burnisher... - Página 31 8. Levante la parte trasera de la máquina para bajar commande vers le haut, comme indiqué à la el alojamiento del disco, tirando de las figure 21. empuñaduras hacia arriba como indicado en la figura 21. CLARKE TECHNOLOGY Operator's Manual - Fusion 20 Burnisher...
-
Página 32: How To Operate The Fusion 20 I
Use the pad pressure gauge to determine the best setting. The needle should stay in the green area. Figure 25 Figure 24 Page -32- CLARKE TECHNOLOGY Operator's Manual -Fusion 20 Burnisher... -
Página 33: Funcionamiento De La Fusion 20I
Para seleccionar el mejor reglaje, mire el l'indicateur de pression du disque: l'aiguille doit indicador de presión del disco: la aguja debe toujours rester dans la zone verte. siempre quedar en la zona verde. CLARKE TECHNOLOGY Operator's Manual - Fusion 20 Burnisher... -
Página 34: How To Operate The Fusion 20 Ix
Use the pad pressure gauge to determine the best setting. The needle should stay in the green area. Figure 28 Page -34- CLARKE TECHNOLOGY Operator's Manual -Fusion 20 Burnisher... -
Página 35: Funcionamiento De La Fusion 20Ix
Pour déterminer le meilleur réglage, consultez siempre quedar en la zona verde. l'indicateur de pression du disque: l'aiguille doit tourjours rester dans la zone verte. CLARKE TECHNOLOGY Operator's Manual - Fusion 20 Burnisher... - Página 36 NOTES...
- Página 37 FUSION 20I/20IX Section II Parts and Service Manual (79002B)
-
Página 38: Maintenance
Wipe any acid from the machine or the tips of the batteries. Do not add acid to battery after installation. Page -38- CLARKE TECHNOLOGY Operator's Manual -Fusion 20 Burnisher... -
Página 39: Mantenimiento
No añade nunca sur la machine ou le ácido en una batería después couvercle des batteries. de su colocación. Ne jamais ajouter d’acide dans une batterie après place- ment. CLARKE TECHNOLOGY Operator's Manual - Fusion 20 Burnisher... - Página 40 See figure 2. 3. Make sure the pad housing and skirt are in correct position. 4. Make sure the pad is installed correctly. 5. Check the pad and pad driver for damage. Page -40- CLARKE TECHNOLOGY Operator's Manual -Fusion 20 Burnisher...
- Página 41 5. Compruebe el buen estado del disco y del 3. Vérifiez que l’ensemble du disque et la jupe sont portadisco. correctement positionnés. 4. Vérifiez que le disque est correctement placé. 5. Vérifiez le bon état du disque et du porte-disque. CLARKE TECHNOLOGY Operator's Manual - Fusion 20 Burnisher...
-
Página 42: Assembly Drawing #1
CLARKE TECHNOLOGY Fusion 20 I and 20 IX Assembly Drawing #1 4/01 Page -42- CLARKE TECHNOLOGY Operator's Manual -Fusion 20 Burnisher... - Página 43 CLARKE TECHNOLOGY Fusion 20 I and 20 IX Assembly Drawing #1 Parts List 4/01 Item # Part No. Description Qty 20i 20ix 55537A Knob, Head Pressure 980638 Washer, Lock 81301A Nut, Jam, 66868A Rod, Adjustment 920181 Nut, -18 ESNA 962980...
-
Página 44: Assembly Drawing #3
CLARKE TECHNOLOGY Fusion 20 I and 20 IX Assembly Drawing #2 6/00 43 12 54 55 40 41 Page -44- CLARKE TECHNOLOGY Operator's Manual -Fusion 20 Burnisher... - Página 45 CLARKE TECHNOLOGY Fusion 20 I and 20 IX Assemby Drawing #2 Parts List 6/00* Item # Part No. Description Qty 20i 20ix 81104A Nut, ¼-20 ESNA 438360 Spring, Brake 87026A Washer, Flat ¼ 848508 Swivel, Brake Rod 67158A Rod, Brake...
-
Página 46: Assembly Drawing #4
CLARKE TECHNOLOGY Fusion 20 IX Assembly Drawing #3 6/00 Beginning with Serial No. XD 59 24 25 44 ref. 41 42 frame ref. frame Page -46- CLARKE TECHNOLOGY Operator's Manual -Fusion 20 Burnisher... - Página 47 59962A Wheel, Traverse (includes #50) 920110 Nut, 5/16-18 Nylock 85814A Screw, -18 x 1¼ 925597 980614 Washer, Star ¼" 699202 Wire Tie 50929A Guard, Lower 50899A Guard, Upper 980657 Washer, 1/4 Lock CLARKE TECHNOLOGY Operator's Manual - Fusion 20 Burnisher...
- Página 48 CLARKE TECHNOLOGY Fusion 20 I and 20 IX Assembly Drawing #4 6/01 Page -48- CLARKE TECHNOLOGY Operator's Manual -Fusion 20 Burnisher...
- Página 49 CLARKE TECHNOLOGY Fusion 20 I and 20 IX Assembly Drawing #4 Parts List 6/01 Item # Part No. Description Qty 20i 20ix 39008B Battery Tray 871334 Battery, 195AH 12 Volt 41206A Series Cable 47380A Key Switch 87052A Washer, Key Switch...
- Página 50 CLARKE TECHNOLOGY Fusion 20 I and 20 IX Assembly Drawing #5 9/98 Page -50- CLARKE TECHNOLOGY Operator's Manual -Fusion 20 Burnisher...
- Página 51 CLARKE TECHNOLOGY Fusion 20 I and 20 IX Assembly Drawing #5 Parts List 9/98 Item # Part No. Description Qty 20i 20ix 32393C Battery, Cover 50721B Bag (package of 10) 30525C Main Body 77267A Label, Tie Down 77091A Label, Moving Parts 170915 Screw, ¼-20 x...
- Página 52 CLARKE TECHNOLOGY Fusion 20 I and 20 IX Pad Drive Motor 2.5 HP / 2000 RPM PN 45001C 9/98 Part No. Description Req'd 833104 Field Assembly 52706A Cover 50628A Board Assembly Brush 50629A Bracket Assembly, Comm. 1 830943 Brush Assembly...
- Página 53 Req'd 912325 Lead Assembly 961028 Bolt 831324 Board Assembly Brush 962730 Screw - 10-24 x 1/2 833105 Frame Assembly 902550 Bearing 55400A 830406 Armature Asm. w/Bearing 980076 Washer, Helical 830949 Brush, Asm. CLARKE TECHNOLOGY Operator's Manual - Fusion 20 Burnisher...
-
Página 54: Volt Battery Charger
CLARKE TECHNOLOGY Fusion 20 I and 20 IX 36Volt Battery Charger 12/95 WARNING: All electrical repairs must be performed by qualified personnel only. PARTS LIST FOR BATTERY CHARGERS 40506A - 36 Volt D.C., 25A, 115 Volt A.C., 60 Hz 40507A - 36 Volt D.C., 25A, 230 Volt A.C., 60 Hz... -
Página 55: Fusion 20 I Electrical Schematic
CLARKE TECHNOLOGY Fusion 20 I Electrical Schematic 1/98 CLARKE TECHNOLOGY Operator's Manual - Fusion 20 Burnisher... -
Página 56: Fusion 20 Ix Electrical Schematic
CLARKE TECHNOLOGY Fusion 20 IX Electrical Schematic 5/99 Page -56- CLARKE TECHNOLOGY Operator's Manual -Fusion 20 Burnisher... - Página 57 CLARKE TECHNOLOGY Fusion 20 IX Connection Diagram 9/98 77269B CLARKE TECHNOLOGY Operator's Manual - Fusion 20 Burnisher...
- Página 58 CLARKE TECHNOLOGY Fusion 20 I Connection Diagram 1/98 Page -58- CLARKE TECHNOLOGY Operator's Manual -Fusion 20 Burnisher...
-
Página 59: Alto ® Product Support Branches
+46 31 706 73 00 Customer Service Headquarters and Factory ALTO Norge A/S, Oslo (Norway) 2100 Highway 265 Bjornerudveien 24 Springdale, Arkansas 72764 N-1266 (501) 750-1000 +47 2275 1770 Technical Service CLARKE TECHNOLOGY Operator's Manual - Fusion 20 Burnisher 1-800-356-7274... - Página 60 (b). Return the product to the nearest Clarke Technology repair location. Transportation charges to and from the repair location must be prepaid by the purchaser. (c). Clarke Technology will repair the product and or replace any defective parts without charge within a reasonable time after receipt of the product.