Format For Gs Compatible Sysex Commands; Table Of Gs Compatible Sysex Commands - Axon AX 100 MKII Manual De Instrucciones

Format for GS Compatible SysEx commands

(Local Mode = Off)
0xF0,
0x41, id, 0x42,
0x12,
ah, am, al,
vv, ..., vv,
xx,
0xF7

Table of GS Compatible SysEx commands

(Local Mode = Off)
Address Databytes
(ah, am, al)
0x40 0x00 0x00 vv vv vv vv
0x40 0x00 0x04 vv
0x40 0x00 0x05 vv
0x40 0x00 0x06 vv
0x40 0x00 0x7F 0x00
0x00 0x00 0x7F xx
0x40 0x01 0x10 vv1 ... vv16
0x40 0x01 0x30 vv
0x40 0x01 0x31 vv
0x40 0x01 0x32 vv
0x40 0x01 0x33 vv
0x40 0x01 0x34 vv
0x40 0x01 0x35 vv
0x40 0x01 0x38 vv
0x40 0x01 0x39 vv
0x40 0x01 0x3A vv
0x40 0x01 0x3B vv
0x40 0x01 0x3C vv
0x40 0x01 0x3D vv
0x40 0x01 0x3E vv
0x40 0x01 0x3F vv
0x40 0x1p 0x02 nn
AXON AX 100 MKII V. 2.0 (Español)
SysEx status
GS Standard address. id=device ID, selected with NRPN 3757
GS Standard data command
Address high, mid, low
Value databytes
Don´t care
End of exclusive
Description
Master tune (default vv = 0x00 0x04 0x00 0x00) -100.0 to +100.0 cents.
Nibbelized data should be used (always four bytes). For example, to tune
to +100.0 cents, sent data should be 0x00 0x07 0x0E 0x08
Master volume (default vv = 0x7F)
Not reset by GS reset.
Master key-shift (default vv = 0x40, no transpose)
Master pan (default vv = 0x40, center)
GS reset
GS reset
Voice reserve :
vv1= Part 10 (default vv = 2)
vv2 to vv10 = Part 1 to 9 (default vv = 2)
vv11 to vv16= Part 11 to 16 (default vv = 0)
Reverb type (vv=0x00 to 0x07), default = 0x04
0x00 : Room1
0x02 : Room3
0x04 : Hall2
0x06 : Delay
Reverb character, default vv = 0x04
Reverb Pre-LPF, 0 to 7, default vv = 0
Reverb master level, default vv = 0x40
Reverb time
Reverb delay feedback. Only if reverb number=6 or 7 (delays)
Chorus type (vv=0 to 7), default = 0x02
0x00 : Chorus1
0x02 : Chorus3
0x04 : Feedback
0x06 : Short delay 0x07 : FB delay
Chorus Pre-LPF, 0 to 7, default vv = 0
Chorus master level, default vv = 0x40
Chorus feedback
Chorus delay
Chorus rate
Chorus depth
Chorus send level to reverb, default=0
MIDI channel to part assign
p is part (0x0 to 0xF)
nn is MIDI channel (0x00 to 0x0F, 0x10=OFF).
This SYSEX allows to assign several parts to a single MIDI channel or to
mute a part.
Default assignment :
part MIDI channel
0 9
1-9 0-8
10-15 10-15
0x01 : Room2
0x03 : Hall1
0x05 : Plate
0x07 : Pan delay
0x01 : Chorus2
0x03 : Chorus4
0x05 : Flanger
(DRUMS)
67