General Safety Recommendations; Envisaged Use And Field Of Application - Aprimatic WING NK Instrucciones Para La Instalación Mecánica

Safety warnings / Use and use limits
2.

GENERAL SAFETY RECOMMENDATIONS

Read the instructions carefully before starting to install
the product.
!
Warning
Packing materials (plastic, polystyrene, etc.) must not be
dispersed in the environment and must not be left where
children can find them as they are a potential source of
danger.
Do not use the product for non-specified or improper
purposes.
Do NOT tamper with or modify the product in any way.
INCORRECT INSTALLATION OF THE MODULE MAY CAUSE
SERIOUS DANGER. FOLLOW ALL THE INSTALLATION
INSTRUCTIONS CAREFULLY.
Only professionally qualified personnel should install the
product.
We recommend operating in a well-lit and healthy environment,
in compliance with the safety regulations in force. We
recommend the use of approved protective clothing (safety
shoes, protective goggles, gloves and helmet). Do not wear
articles of clothing that could get caught.
Take adequate safety measures to prevent the risk of injury
caused by sharp splinters and the possible risks of crushing,
knocks and cuts or amputation.
Delimit the yard to prevent any unauthorised persons from
transiting in the working area. Do not leave the working
area unattended.
Due to the moving, traversing and rotating parts, when the
cover guard is dismantled or open, there is great danger of
getting your hair, clothes, or cables etc. caught in the moving
machine members.
We recommend strict observation of the national regulations
for safety in work sites (in Italy, Legislative Decree 528/99
coordinated with Legislative Decree 494/96 "Implementation
of Directive 92/57/EEC concerning the minimum rules and
regulations on health and safety at work to be observed when
working on temporary or mobile sites").
Installation, electrical connections and adjustments must be
carried out in a professional manner in compliance with the
Good Manufacturing and Workmanship regulations in force in
the country where the automation is installed.
The manufacturer of the device is not responsible for the
non-observance of professional standards of work in the
construction of the power-driven structure, nor for any damage
which may be caused by the use of the drive.
Incorrect installation may be dangerous.
Follow the manufacturer's instructions.
Before starting installation, check that the product is intact and
that the existing structure is suitably strong and stabile.
Information
Only specialised technicians, trained to do the job, should
test and put the door into service, as well as carrying out
the periodic checks and any maintenance.
We strongly recommend following a specialised training
course. Installers should contact the supplier for
information on courses.
At the end of the work the installer must check the installation
is done correctly and the automation works properly.
The automation cannot be tested and put into service until
the sliding door has been verified as being conform to the
standards of MACHINERY DIRECTIVE 89/392/EEC, to which
the complete door, fitted and installed, is subject. The installer
must at all times use and keep at all times the TECHNICAL
DOSSIER of the automatic door and must follow all of the
provisions contained in it.
He shall assess the risks connected to the operation of the
sliding door and be sure there are no dangerous crushing or
shearing points. If necessary special preventive measures
must be taken and all of the signs required by the regulations
in force to warn of any dangerous zones must be attached..
Every installation must clearly indicate the ID data for the
power-driven system.
The installer must provide all the information about the
automatic, manual and emergency functioning of the power-
driven door and deliver the corresponding instructions to
the system user.
Only use original spare parts for any repairs or for replacing
parts. The guarantee is void if this product is used in
combination with others of other brands.
The manufacturer of the drive declines any responsibility if
components incompatible with safety and correct operation
are installed.
3. ENVISAGED USE AND FIELD OF
APPLICATION
The Module is the base for simple and fast creation of a
very vast range of finished automatic doors as it provides
the basic automation components pre-assembled on a
single support.
The WING NK Module has been designed and manufactured
exclusively for use on automatic doors with one or two
horizontal sliding wings created using the Aprimatic NK
Beam system.
It is used in civil, public or industrial applications, in dry areas,
in covered entrance areas and foot traffic passageways.
!
Warning
• Do not use the product for non-specifi ed or improper
purposes.
• Do not tamper with or modify the product.
• The product must only be installed using APRIMATIC
material.
8
- -