Display Menu - Levenhuk Blaze D500 Guia Del Usuario

then you can start the preview on the screen.
Focusing adjustment
Look through your digital spotting scope at a distant object. Rotate the focusing wheel (1)
until the view is focused.
Digital zoom
Push the digital zoom button on the body of the digital spotting scope (11) or on the
capture remote control (16) to zoom in or zoom out.
Capturing an image or recording a video
1) Insert a microSD card into the microSD slot (9). Maximum card size is 64GB.
2) Turn the Focus adjustment wheel (1) to focus the image of your object to its best focus.
3) Press the Capture button on the body of the digital spotting scope (7) or on the capture
remote control (17) and the photo will be saved to the microSD card.
4) To switch to video recording mode, press the Photo/Video/Playback button (6). Then,
press the Capture button on the body of the digital spotting scope (7) or on the capture
remote control (17) to start video recording. Press the Capture button again to stop video
recording.
Playback
1) Insert a microSD card into the slot (9).
2) Press the Photo/Video/Playback button on the body of the digital spotting scope (6) or
on the capture remote control (15) to switch to playback mode.
3) Press the Up (4) and Down buttons (5) to scroll the previous captured photos and
videos.
Deleting files
1) Insert a microSD card into the slot (9).
2) Press the Photo/Video/Playback button on the body of the digital spotting scope (6) or
on the capture remote control (15) to switch to playback mode.
3) Press the Setup button (3) to choose a file to delete.
Mass storage on PC
1) Insert a microSD card into the slot (9).
2) Connect the digital spotting scope to your PC with the USB cable to download images
from the card to your computer.

Display menu

Press the Setup button (3) to open the main display menu. From this menu, you can set
the image and video resolution, adjust image exposure, set the interface language, turn
the power saving mode on, set the date and time up, turn HDR and capture mode on, set
the TV connection up, format the SD card, reset the settings, and check the hardware
version. In addition, this menu provides access to the Loop recording mode and the Date
Stamp option.
Resolution
Select the image or video Resolution from the main menu and choose the required
resolution by pressing the Down button (4), and then confirm by pressing the Capture
button (7).
4
Note: This model supports the following image resolutions: 14M, 12M, 10M, 8M, 5M; video
resolutions: 1080P, 720P.
Capture Mode
In photo mode, press the Setup button (3) to choose Capture Mode and set the intervals
between the photos. For example, you can set up the digital spotting scope to take a
photo every 5 seconds.
Exposure (Brightness)
Select Exposure from the main menu and then select a target value by pressing Up (4) or
Down (5) buttons. You can also use the Up and Down buttons in photo mode to increase
or decrease the exposure. Exposure control is used to get a better image when the
environment light is too high or too low.
Date Stamp
In photo mode, press the Setup button (3) to select Date Stamp. This option allows you to
add date and time mark the photos and videos.
Date and time
Select Date/Time from the main menu and press the Setup button (3) twice to set the
current date and time. Press the Capture button (7) to confirm entry.
TV connection
Select TV Mode from the main menu and press the Setup button (3) twice to select
between NTSC and PAL, the correct mode compatible with your TV. Press the Capture
button (7) to confirm selection.
Loop recording
Select the duration of the video clip to turn on the Loop recording mode. In case the Loop
recording mode is on, and the microSD card memory is full, the video clip of the selected
duration will be recorded over the previous one.
HDR
In video mode, press the Setup button (3) to turn HDR on or off. Use HDR mode to
capture low-light and backlit scenes: HDR will help brighten up the dark areas of the
image without spoiling the well-lit areas.
Power saving
Select Auto Power Off from the main menu and set the idle time before the digital spotting
scope automatically shuts down. Press the Capture button (7) to confirm selection.
Language
Select Language from the main menu and press the Setup button (3) twice to choose one
of the existing settings. Press the Capture button (7) to confirm selection.
MicroSD card formatting
Select Format SD from the main menu press the Setup button (3) twice to format the
installed memory card. All the files on the card will be deleted after card formatting.
Normally card formatting is not necessary, unless your card is not able to store the
captured image.