Pipe Preparation - Victaulic I-900 Instrucciones De Armado

PRODUCTS FOR
PLAIN END HDPE PIPE

PIPE PREPARATION

Victaulic HDPE products are designed to mechanically join high density polyethylene/polybutylene pipe
conforming to ASTM D-2447, D-3000, D-3035 or F-714, at ambient temperatures and of wall thicknesses
from SDR 32.5 to 7.3.
Victaulic Metric HDPE products are designed to mechanically join HDPE (high density polyethylene/poly-
butylene pipe conforming to ISO 161/1, AS 1159 and DIN 8074 dimensional specifications) pipe of wall
thicknesses from SDR 32.5 to 7.3.
Victaulic HDPE products have integral rows of gripping teeth in each side of the housing which bite into
HDPE pipe around the entire circumference. Victaulic HDPE products are not intended for use on PVC
pipe. Victaulic lubricant is NOT recommended for use with HDPE pipe.
HDPE pipe brands we have tested indicate that the working pressure of Victaulic HDPE products are dic-
tated by the working pressure of the pipe. The pipe manufacturers listing is dependent upon wall thick-
nesses, pipe composition and temperature.
Pipe outside diameter must be within tolerances shown for each individual size and style and is subject to the specific
standards for acceptability listed.
Failure to follow these instructions could result in personal injury, property damage, improper installation, joint leak-
age or joint failure.
PIPE SIZE/TOLERANCES – IMPERIAL (ANSI/IPS)
Pipe – In./
mm
Nom. Act.
Size Size
2 2.375
50 60.3
3 3.500
80 88.9
4 4.500
100 114.3
5 5.563
125 141.3
6 6.625
150 168.3
8 8.625
200 219.1
*At ambient temperatures.
† Contact Victaulic for special bolt/nut requirements.
PIPE SIZE/TOLERANCES – METRIC (DIN and others)
Pipe O.D. – mm
Min. O.D. Max. O.D.*
90 90.9
110 111.0
140 141.3
160 161.5
*Tolerances at ambient temperatures for pipe with SDR of 20 or lower.
Dimensions – In./
Outside Dia.
Size Tol. *
2.375 ± 0.016
60.3 0.406
3.500 ± 0.016
88.9 0.406
4.500 ± 0.020
114.3 0.508
5.563 ± 0.025
141.3 0.635
6.625 ± 0.030
168.3 0.762
8.625 ± 0.039
219.1 0.990
§ See pipe manufacturer for maximum out of round tolerance.
Pipe O.D. – mm
Min. O.D. Max. O.D.*
200 201.8
225 227.1
250 252.3
Pipe – In./
mm
Max.
Out of
Round Nom.
Tol.* Size
± 0.040 10
1.016 250
± 0.040 12
1.016 300
± 0.040 14 †
1.016 350
± 0.050 16
1.270 400
± 0.050 18
1.270 450
± 0.075 20
1.905 500
Pipe O.D. – mm
Min. O.D.
280
315
355
Dimensions – In./
mm
Outside Dia.
Act.
Size Size
10.750 10.750
273.0 273.0
12.750 12.750
323.9 323.9
14.000 14.000
355.6 355.6
16.000 16.000
406.4 406.4
18.000 18.000
457.2 457.2
20.000 20.000
508.0 508.0
Pipe O.D. – mm
Max. O.D.* Min. O.D.
282.6 400
317.9 450
358.2 500
I-900
19.01-1A
mm
Max.
Out of
Round
Tol. * Tol.*
± 0.048 ± 0.075
1.219 1.905
± 0.057 ± 0.075
1.448 1.905
± 0.063 ± 0.075
1.600 1.905
± 0.072
§
1.830
± 0.081
§
2.060
± 0.090
§
2.290
2029-1A
Max. O.D.*
403.6
453.8
504.0
5