Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
English
assemble the protective cover and tighten all
screws (10/H and 10/I);
Dust extraction
Your wall chaser is equipped with a dust extraction system:
use the machine with a suitable dust remover. Connect an
industrial vacuum cleaner to the D connector making sure
the vacuum cleaner is suitable for think dust.
Fastening the work piece and size of the
work piece
if the work object is a block and not part of a
structure, fasten it in order to prevent its movement;
prevent the work piece from shifting, moving or
falling when you are cutting.
Setting cutting depth
Some models allow the user to set the cutting depth. This is
carried out by turning the device shown in figure 12.
Unscrew and remove the wing-nut;
Insert the wing-nut into one of the positions;
Screw the wing-nut.
Environmental conditions
do not expose the wall chaser to rain, ice or snow;
prevent water or any other liquid from coming into
contact with the electrical parts of your machine;
do
not
use
the
atmospheres, for instance flammable liquids, gas or
dust. The electric wall chaser produces sparks
which can ignite fumes, dust or smoke.
O
p
e
r
a
t
i
n
g
O
p
e
r
a
t
i
n
g
After having followed the instructions given in the previous
Preliminary operations paragraph, proceed as follows in
order to perform the cut.
Warning: do not touch any moving parts of
your wall chaser, in particular the blade, when
operating.
switch the vacuum cleaner on;
locate the position of the groove. Position the wall
chaser, switch it on and press on the handles letting
the blades penetrate into the work piece;
pull the machine toward you to perform the cut.
Your wall chaser is intended to perform straight
cuts only;
for your safety, hold the wall chaser with both
hands as shown in figure 3 and 4;
cutting materials containing wood, cork, rubber,
foam polystyrene can result in problems moving
forward the machine. If you have this kind of
problems, stop cutting and remove all materials
listed before and proceed with cutting operations. If
you cannot remove these materials, stop cutting
and cut in another position;
when you complete the cut, switch off your wall
chaser and wait till the blade comes to a complete
stop.
Watch out! The blade
very hot and cause severe burns.
We recommend to use a wooden lath that helps performing
straight cuts.
wall
chaser
in
explosive
I
n
s
t
r
u
c
t
i
o
n
s
I
n
s
t
r
u
c
t
i
o
n
s
and the cutting area can be
Electronic devices
Your wall chaser is equipped with a CARDI multifunction
electronic device that includes a soft-start and an electronic
clutch:
the soft-start allows the motor to start gradually,
reducing peak current that occurs when you switch
the motor on, helps you when you begin cutting,
allowing gradual blade rotation and avoiding jerks
at the operator's arm. The soft-start allows you to
use your wall chaser connected to household
outlet;
the electronic clutch cuts off power to the motor in
case of excessive overload, increasing the operator
safety and preventing damage to the motor. When
the overload is over, the device gives back power to
the motor that begins working again;
if the electronic clutch operates frequently means
that the wall chaser is not used properly. Possible
causes can be a not suitable forward speed, an
excessive friction between the blade-side and the
material, excessive cutting depth. In these cases,
stop cutting and let the machine turn with no load
for some seconds, helping the motor cool down.
M
a
i
n
t
e
n
a
n
c
e
-
M
a
i
n
t
e
n
a
n
c
e
-
Periodic maintenance
at the end of the work, after having removed the
blade, blow compressed air inside the rotating
motor in order to remove dust and powder. Do this
operation wearing protective goggles;
before starting any other cleaning, maintenance or
lubrication operation make sure that the wall chaser
is unplugged;
keep your wall chaser clean and dry, in particular its
handles and its moving parts;
never use solvents or other harsh chemicals for
cleaning your wall chaser;
after use put your wall chaser in a dry, safe place
inaccessible to children place;
gears are lubricated by lubricating oil and grease
which are suited for any external temperature. You
don't have to check the oil level or to fill it up.
always unplug the wall chaser during check or
blade replacement;
never unplug the wall chaser by pulling the cord;
inspect often the power cable and extension cords,
making sure that they don't have any damage like
cuts, abrasions or exposed wires. If you find a
damage, ask to a CARDI authorized service centre
for replacement;
do not use the wall chaser with damaged
components or with malfunctions, in particular when
the switch doesn't work properly. In these cases,
ask a CARDI authorized service centre for
replacement.
Service
after 250 hours of work, bring your wall chaser to a
CARDI authorized service centre for periodical
check;
any repairing on your wall chaser must be carried
out by CARDI authorized service personnel only.
Ask your dealer for the list of the CARDI authorized
service centres;
your machine's serial number is stamped on the
machine or printed on the data plate as shown in
figure 7;
S
e
r
v
i
c
e
-
W
a
r
r
a
S
e
r
v
i
c
e
-
W
a
r
r
a
8
n
t
y
n
t
y
Publicidad
Tabla de contenido
