Operating Information - Simu RSA Manual De Instrucciones

4.5.1- Choose the remote control key's function to program:
- Display the value of the function to program using
4.5.2- Save the channel (RSA Hz can save maximum 32 channels):
- Press simultaneously the remote control key to program and the key
seconds until dashes appear
- The RSA Hz can be controlled in the three-button mode using a reverter with three keys wired onto the START,SEC2, and SEC3 inputs (if the latter are configured
"non wired": chapter 4.2).
4.6- Clearing remote controls: Parameter
- Clearing all remote controls is performed by pressing and holding for 3 seconds the key
until dashes appear.
4.7- Configuration of auxiliary accessories: Parameter
- The auxiliary contact is a dry contact. A single accessory can be connected and power supplied according to the use configured.
Contact to drive an electric latch
(The latch must be supplied with an outside power supply)
Contact to drive an electromagnetic latch
Contact to drive an Orange flashlight without notice
(only during the door's operation)
Contact to drive an Orange flashlight with notice
(before starting and during the door's operation)
4.8- Configuring the operating time: Parameters
- : Motor operating time (factory setting =
> (increments of 1 sec.) Adjust a time slightly longer than the actual operating time (opening time + 3s.).
- : Time for reclosing the door (valeur usine =
> (increments of 1 sec.) Enabled in automatic operating mode (§ 4.1).
- : Delay time before motor reversion (factory setting =
> (increments of 1 sec.) Particular case of motors not accepting reversion of the rotation direction without stopping phase.
- : Area lighting time after cycle end (factory setting =
> (increments of 1 minute.)
To return to the menu, press the
waiting time.
5

Operating information

List of operating information displayed by RSA Hz used to view and an easy diagnostic of the facility's status.
Event codes:
Waiting for a command
Opening door in progress
Delay before closing door
Closing door in progress
Opening cell hidden
Closing cell hidden
Log of the last 10 faults:
Cycles counter: Tens and units,
Accessories consumption:
Reset of the RSA Hz after a fault: To clear the fault codes, select the parameter
- For the fault codes from
- For the fault codes from
*If the connection of accessories matches the diagram in chapter 1.
**Area Dangerous forMovement Accessible to the Public.
4/4
and
(factory setting =
(valeur usine =
- )
)
)
) Check that the value of the parameter
)
and keys to return to value
ADMAP* cell hidden
Door movement forced by keypad
Emergency stop triggered
Safety Self-testing
Permanent contact on "START" input
Delay before motor reversion
: See fault code above.
Thousands and hundreds,
: Puissance consommée en watts de
to : Once the fault is corrected, it is not required to clear the fault code of the log to return to normal operation.
to : Once the fault is corrected, you must clear the defect code for the log to return to normal operation.
keys on the RSA Hz.
on the RSA Hz for three
)
)
Contact to drive a zone lighting
(default mode, automatic switch off after timeout T3 - §4.8)
Contact to drive an open door indicator
Contact of the stable mono relay type to drive an automation system
Contact of the unstable relay type to drive an automation system
(or any other value indicating the product's operation: see §5) or after a one-minute
Safety fault at opening
(contact always open)
Safety fault at closing
(contact always open)
ADMAP* safety fault
(contact always open)
Self-test failed on safety input 1
Hundred and tens of thousands, (example :
à
then press and hold the
is equal to
Default codes:
Self-test failed on safety input 2
Self-test failed on safety input 3
Intensity exceeded on 24V power supply
(too many accessories connected)
Operating time "T0" too short
or motor endstop not reached
U2 U1 U0
= 5249 cycles).
key for 3 seconds until dashes
3s.
3s.
appear.