Makita RS001G Manual De Instrucciones página 12

WARNING:
BE SURE TO TIGHTEN THE HEX
BOLT COUNTERCLOCKWISE SECURELY. Also be
careful not to tighten the bolt forcibly. Slipping your
hand from the hex wrench can cause a personal injury.
WARNING:
If the ring is needed to mount the
circular saw blade onto the spindle, always be sure that
the correct ring for the blade's arbor hole you intend to
use is installed between the inner and the outer flanges.
Use of the incorrect arbor hole ring may result in the
improper mounting of the circular saw blade causing blade
movement and severe vibration resulting in possible loss of
control during operation and in serious personal injury.
Blade guard cleaning
When changing the circular saw blade, make sure to
also clean the upper and lower blade guards of accu-
mulated sawdust as discussed in the Maintenance
section. Such efforts do not replace the need to check
lower guard operation before each use.
Connecting a vacuum cleaner
Optional accessory
NOTE: To prevent the rubber cap from being lost,
store it on the front of the tool.
NOTE: When not using the vacuum cleaner, attach
the rubber cap onto the dust nozzle.
Remove the rubber cap from the dust nozzle and con-
nect the vacuum cleaner's hose.
► Fig.21: 1. Rubber cap
When you wish to perform clean cutting operation, connect
a Makita vacuum cleaner to your tool. Connect a hose of the
vacuum cleaner to the dust nozzle using the front cuff 24.
► Fig.22: 1. Hose of the vacuum cleaner 2. Front cuff
24 3. Dust nozzle 4. Rubber cap
OPERATION
This tool is intended to cut wood products only.
Refer to our website or contact your local Makita dealer
for the correct circular saw blades to be used for the
material to be cut.
Checking blade guard function
Set the bevel angle to 0°, and then retract the lower
guard manually to the end and release it. The lower
guard is properly functioning if;
— it is retracted above the base without any hin-
drance and;
— it automatically returns and contacts with the
stopper.
► Fig.23: 1. Upper guard 2. Lower guard 3. Base
4. Stopper 5. Open 6. Close
If the lower guard is not functioning properly, check if
saw dust is accumulated inside of the upper and lower
guards. If the lower guard is not functioning properly
even after removing dust, have your tool serviced at a
Makita service center.
CAUTION:
Wear dust mask when performing
cutting operation.
CAUTION:
Be sure to move the tool forward
in a straight line gently. Forcing or twisting the tool
will result in overheating the motor and dangerous
kickback, possibly causing severe injury.
NOTE: When the battery cartridge temperature is
low, the tool may not work to its full capacity. At this
time, for example, use the tool for a light-duty cut for
a while until the battery cartridge warms up as high
as room temperature. Then, the tool can work to its
full capacity.
► Fig.24
Hold the tool firmly. The tool is provided with both a front
grip and rear handle. Use both to best grasp the tool.
If both hands are holding saw, they cannot be cut by
the circular saw blade. Set the base on the workpiece
to be cut without the circular saw blade making any
contact. Then turn the tool on and wait until the circular
saw blade attains full speed. Now simply move the tool
forward over the workpiece surface, keeping it flat and
advancing smoothly until the sawing is completed.
To get clean cuts, keep your sawing line straight and
your speed of advance uniform. If the cut fails to prop-
erly follow your intended cut line, do not attempt to turn
or force the tool back to the cut line. Doing so may bind
the circular saw blade and lead to dangerous kickback
and possible serious injury. Release switch, wait for cir-
cular saw blade to stop and then withdraw tool. Realign
tool on new cut line, and start cut again. Attempt to
avoid positioning which exposes operator to chips and
wood dust being ejected from saw. Use eye protection
to help avoid injury.
Hook
CAUTION:
Always remove the battery when
hanging the tool with the hook.
CAUTION:
Never hook the tool at high loca-
tions or on the surfaces where the tool may lose
the balance and fall. Otherwise falling accident may
occur and cause serious injury.
CAUTION:
Do not pull the tool downward
when it is hooked.
CAUTION:
Use the hanging/mounting parts
for their intended purposes only. Using for unin-
tended purpose may cause accident or personal
injury.
The hook is convenient for hanging the tool temporarily.
To use the hook, simply lift up hook until it snaps into
the open position.
When not in use, always lower hook until it snaps into
the closed position.
► Fig.25: 1. Hook 2. Open position 3. Closed position
► Fig.26
12 ENGLISH