RS Pro RS-172 Manual De Instrucciones página 3

Temperature & Humidity Datalogger/English
Specification:
Overall Range:0~100%
Accuracy(0 to 20 and 80 to 100%)
Relative
Humidity
Accuracy(20 to 40 and 60 to 80%)
Accuracy(40 to 60%)
o
Overall Range: -40~70 C，-40~158
Accuracy: -40 to -10 and +40 to +70°C
Accuracy: Accuracy: -10 to +40°C
o o
Accuracy: -40~14 F，104~158 F
o
Accuracy: 14~104 F
Overall Range: -200 to 1300 o C，-328 to 2372
Accuracy: -100 to 1300 o C
Temperature
Accuracy: -200 to -100 o C
K1, K2
o
Accuracy: -148 to 2372 F
o
Accuracy: -328 to -148 F
1 sec. to 12h
Measuring
rate
1 sec to 24h
67584(each for Temperature, Humidity, Temp.K1, Temp.K2)
Memory
32700 values
Battery type 3.6V lithium
3 months(rate at 5sec.)depending on measuring rate and use of
Battery life
alarm leds
Size(Weight) 94 mm × 50 mm × 32 mm (91g)
Analysis
Windows 98/2000/xp/vista/7
software
o
Resolution 0.1%RH, 0.1 C
2
RS- RS-
172 172TK
±5.0%
* *
±3.5%
±3.0%
o
F
o
±2 C
o
±1 C * *
o
±3.6 F
o
±1.8 F
o F
±0.15%rgd+1.0 o C
o *
±0.5%rgd+2.0 C
o
±0.15%rgd+1.8 F
o
±0.5%rgd+3.6 F
*
*
*
*
* *
* *
* *
* *
* *
22/12/2017 Version No. 001
Temperature & Humidity Datalogger/English
Operation Instructions:
1.Battery sign When battery is exhausted,
sign will be displayed. At this time, replacing
a new battery is necessary. The useful life of the
battery is more than 3 months.
2.TIME currently time
3.DATE currently data
4.Time and date are automatically switch mode and it
will switch for every 10s
5.MAX display maximum value during measuring
6.MIN display minimum value during measuring
7.REC sign showing that the data logger is under recording
8.FULL sign showing that the memorizer is full, the data logger will stop recording
9.%RH sign showing that the data logger is measuring humidity
10.°C - Centigrade
11.°F - Fahrenheit
12.When pressing the MAX/MIN button, it will hold MAX,MIN and time and date.The
time and date is also switched for every 10s. If you do not press any key within 40s, the
meter will automatically exit from the MAX MIN mode and return to the the data hold and
measure mode.
13.When loading the data, there will be "-PC-" sign displayed on the LCD. After all the
data is loaded, the data logger will display the real value from current measurement, but
will stop recording. The logger needs to be re-set if you need the recording function.
You can only view the data from the logger itself.
All settings will be only carried through the software installed in PC.
14.Alarm function
When the measured value exceeds the set upper limit or lower limit, the alarm LED will
blink one time per minute. Blinking Red LED shows temperature value exceeds limit, while
blinking Yellow LED shows humidity value exceeds limit.
When the measured value exceeds the set upper limit or lower limit, the alarm LED will
blink at the recording rate. Red LED blinking twice quickly shows TK1 temperature value
exceeds high limit or blinking once shows TK1 temperature value below low limit. While
Yellow LED blinking twice shows TK2 value exceeds high limit or blinking once shows
TK2 temperature value below low limit (RS-172TK).
22/12/2017 Version No. 001
3