Ryobi RBC-1000EX Manual De Utilización página 22

GB
F D E
ASSEMBLY
Slide the bolt (16) through the hole in the front handle.
■
Slide the washer (17) onto the bolt.
■
Place the barrier handle (15) onto the bolt and tighten
■
the barrier handle securely.
ATTACHING THE BLADE GUARD OR THE
GRASS DEFLECTOR (FIG.4 & FIG.5)
Follow these steps to attach the blade guard (Fig. 4)
Attach the blade guard (11) to the mounting bracket
■
(31).
Install two screws (18) from the top of the mounting
■
bracket (31) through the blade guard (11) and into the
threaded mounting plate (35).
Follow these steps to attach the grass deflector (Fig. 5)
Attach the trimmer guard to the gear case.
■
Install three screws (18) through the guard and into to
■
gear case.
EXTENSION CORD RETAINER (FIG.6)
An extension cord retainer (4) is located on the bottom of
the trimmer. This provides strain relief for the cord,
preventing unwanted disconnects.
Use the extension cord retainer when you connect
■
the extension cord to the power cord to prevent
disconnection. Use only an outdoor approved
extension cord.
Loop the extension cord through the extension cord
■
retainer slot located on the bottom end of the trimmer.
Pull loop of extension cord around tongue and pull tight.
■
Attach extension cord to plug on trimmer.
■
SHOULDER STRAP (FIG.7)
A shoulder strap (10) is supplied for your greater comfort.
Simply attach the clip (20) of the shoulder strap onto
■
the hanger (21) at the front of the motor housing (5).
CONVERTING FROM STRING TRIMMER TO
BRUSHCUTTER (FIG.4 & FIG.5)
REMOVING THE STRING HEAD
Align the slot in the upper flange washer (28) with the
■
hole in the gear head (27). Place a holding pin
through the slot in the upper flange washer and the
hole in the gear head. Turn the bump knob (22)
clockwise to remove. Remove the spool (24) and
trimmer head (25) from the drive connector (26).
I P NL S DK N FIN GR HU CZ RU
English
Place the holding pin through the upper flange
■
washer and the gear head. Using a 17 mm wrench,
turn the drive connector clockwise to remove.
Remove the upper flange washer from the gear shaft
■
and retain for blade installation.
Remove the grass deflector.
■
Note: Store the string head parts together for later use.
INSTALLING THE BLADE
Place the upper flange washer over the gear shaft
■
with the hollow side towards the blade guard.
Centre the blade on the upper flange, making sure
■
the blade sits flat. Install the cupped washer (29) with
the raised centre away from the blade. Install the
blade nut (30). The blade (12) turns counterclockwise
from the operator's position.
Place the holding pin through the slot in the upper
■
flange washer and the hole in the gear head (27).
Using a 17 mm wrench, turn the blade nut
counterclockwise.
Tighten nut securely.
■
Install the blade guard.
■
CONVERTING FROM BRUSHCUTTER TO
STRING TRIMMER
REMOVING THE BLADE
Place the holding pin through the slot in the upper
■
flange washer and the gear head. Turn the blade nut
clockwise to remove.
Remove the cupped washer and the blade.
■
Remove the upper flange washer from the gear shaft
■
and retain for the string head installation.
Remove the blade guard.
■
Note: Store the brushcutter parts together for later use.
INSTALLING THE STRING HEAD
Install the upper flange washer onto the gear shaft
■
with the hollow side towards the gear head.
Place the holding pin through the slot in the upper
■
flange washer and the hole in the gear head. Using a
17 mm wrench, turn the drive connector anticlockwise
to install. Tighten securely.
Place the trimmer head on the drive connector.
■
Place the holding pin through the slot in the upper
■
flange washer and the hole in the gear head. Install the
bump knob and turn anticlockwise to tighten securely.
Install the grass trimmer guard.
■
16
RO PL SLO HR TR EST LT LV SK BG