GE 36240 Manual

http://waterheatertimer.org/Programmable.html
Indoor
Wireless Remote with Countdown
Lighting Control
Manual
A B1 B2 B3
assembled in package
ENCLOSED YOU WILL FIND:
B3� Wallplate bracket
A� Plug-in receiver
C� Mounting screws and anchors
B1� Remote transmitter
D� CR2032 battery
B2� Remote wall mount
INSTALLING BATTERY (REMOTE) [FIG.1]
1� Find the remote and CR2032
battery (included in package)�
2� Remove transmitter from the remote wall
mount — push down and out from the top
of the remote ("I" button is on top)[FIG.5]�
3� Turn remote over and pull out
battery drawer [FIG.1]�
4� Place battery in the drawer with (+)
side of the battery facing up�
5� Push the battery drawer back into remote�
(Red indicator light on the front of remote should light up when a button is pushed.)
INSTALLATION INSTRUCTIONS (ON/OFF RECEIVER)
1� Plug lamp or the device to be controlled into the outlet on the side of
the receiver� Make sure lamp or device is turned to the ON position�
2� Plug the receiver into a standard indoor outlet�
3� Wait 5 seconds for the receiver to activate�
IMPORTANT: It will take 5 seconds from the time the receiver is
plugged into the outlet before the remote will be functional.
MOUNTING REMOTE OPTIONS
OPTION 1 OPTION 2
OR OR
OPTION 1: WALL MOUNT WITH OR WITHOUT WALLPLATE
1� Place remote mount with wallplate bracket
where mounting, and mark the remote mount
holes on the wall [FIG.2]� Arrows on the back
of remote mount indicate the top [FIG.3]�
2� If mounting directly to a stud, drill holes using
a 3/32" drill bit (anchors will not be used)�
3� If mounting to drywall, drill holes using
a 1/4" drill bit� Gently tap in anchors�
4� Remove wallplate bracket if mounting
without a wallplate�* Leave the wallplate
bracket on if using a wallplate�
*To separate the remote mount from the wallplate bracket, hold the wallplate
bracket by the wallplate holes. Turn the wallplate bracket so you are looking
at the arrows [FIG.3]. Gently push the remote out of the wallplate bracket.
5� Screw in remote mount using mounting screws� Do not overtighten�
6� Screw on wallplate (not included)�
7� Proceed to INSERTING AND REMOVING REMOTE�
NOTE: If reassembling the wallplate bracket with the remote mount, verify the that
the arrows line up on the back of the remote mount and wallplate bracket [FIG 3].
OPTION 2: WALL MOUNT WITH EXISTING WIRED SWITCH
1� Screw the remote mount with wallplate bracket onto the
wallplate that will be used (not included)� This will now be
the wallplate bracket assembly (B2, B3 & wallplate)�
2� Place the wallplate bracket assembly on the existing
switch box and mark the remote mount holes�
3� If mounting directly to a stud, drill holes using a
3/32" drill bit (anchors will not be used)�
C
4� If mounting to drywall, drill holes using a 1/4"
drill bit� Gently tap in anchors�
5� Place wallplate bracket assembly into place, and screw in the
wallplate to the existing switch, as well as screwing the wall mount�
D
INSERTING AND REMOVING REMOTE
FROM WALL MOUNT
INSERTING
1� Place bottom of remote over the spring tab
in the remote bracket, gently press down
and push into the remote bracket� [FIG. 5]
2� Remote should snap in and
be held firmly in place�
FIG. 1
REMOVING
1� Gently push the top of the remote down
and out from the remote mount� [FIG. 5]
NOTE: May not work with screwless wallplates.
PAIRING AND UNPAIRING RECEIVER
(LIGHTING CONTROL COMES PAIRED IN THE PACKAGE� THIS SHOULD
ONLY BE NEEDED IF ADDING REMOTES AND/OR RECEIVERS OR
IF YOUR LIGHTING CONTROL HAS BECOME UNPAIRED)
PAIRING — LINKING REMOTE TO RECEIVER
1� Make sure the receiver is not plugged into the outlet
and the remote is close with battery installed�
2� Plug receiver into the outlet�
3� Within the first 5 seconds after plugging in, press and
hold any button on the remote for 2 seconds�
4� After 5 seconds from plugging the receiver into the
outlet, the remote and receiver will be paired�
UNPAIRING — REMOVING ALL PAIRED DEVICES FROM RECEIVER
1� Hold down the ON and the OFF buttons at the same time for 5 seconds�
2� Receiver will delete ALL transmitters programmed in it�
REMOTE FUNCTIONALITY
1� Use "I" and "O" buttons to turn the light ON/OFF�
2� Press the countdown option to keep the light ON for the chosen period of
time� The light will then automatically shut off�
FIG. 2
FIG. 3
TROUBLESHOOTING
Problem
Indicator light on remote
does not light up red
when button is pushed
Indicator light on
remote lights up and
light does not turn on
Wallplate does not fit on
wall mount correctly
Wallplate screws are too
long and hit the wall
PLUG-IN RECEIVER
Functional Range ����������������������������������������������������������������������������������������������������������������up to 150ft
Maximum Tungsten Load ����������������������������������������������������������������������������������������������������������360W
Maximum Resistive Load ��������������������������������������������������������������������������������������������������������1440W
Rating ��������������������������������������������������������������������������������������������������������������������������12A / 120V / 60Hz
REMOTE TRANSMITTER
Functional Range ����������������������������������������������������������������������������������������������������������������up to 150ft
Battery Type �����������������������������������������������������������������������������������������������������������������������������������CR2032
* Functional range may be adversely affected by one or more of the
following factors: weather, radio frequency interference, low transmitter
battery and obstructions between the transmitter and receiver.
FCC STATEMENT
FIG.4
This device complies with Part 15 of the FCC and Industry Canada license-exempt
RSS standard(s)� Operation is subject to the following two conditions: (1 this device
may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation�
FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused
by unauthorized modifications to this equipment� Such modifications could void the
user's authority to operate the equipment� NOTE: This equipment has been tested
and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules� These limits are designed to provide reasonable protection against
harmful interference in a residential installation� This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with
the instructions may cause harmful interference to radio communications� However,
there is no guarantee that interference will not occur in a particular installation� If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
FIG.5
• Reorient or relocate the receiving antenna�
• Increase the separation between the equipment and receiver�
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected�
• Consult the dealer or an experienced radio/TV technician for help�
CAN ICES-3(B)/NMB-3(B) | FCC: Q2I16I8278 | IC: 6924A-JP831071L8
WARNING
BATTERY MAY LEAK HARMFUL LIQUIDS OR IGNITABLE
MATERIALS OR EXPLODE CAUSING INJURY OR PRODUCT
DAMAGE�
• REPLACE FULLY DISCHARGED BATTERY IMMEDIATELY
• REMOVE BATTERY IF PRODUCT IS TO BE UNUSED FOR
EXTENDED PERIOD OF TIME
RISK OF ELECTRIC SHOCK
• FULLY INSERT PLUG
• KEEP CHILDREN AWAY
• USE INDOORS ONLY
• DO NOT USE IN WET LOCATIONS
• UNPLUG BEFORE CLEANING
RISK OF FIRE
• DO NOT EXCEED ELECTRICAL RATINGS
• DO NOT USE TO CONTROL MOTOR-OPERATED
APPLIANCES, TRANSFORMER-SUPPLIED APPLIANCES
OR APPLIANCES THAT CONTAIN HEATING ELEMENTS
(COOKERS, IRONS, HEATERS, ETC�)
MADE IN CHINA
GE is a trademark of General Electric Company and is under license by
Jasco Products Company LLC, 10 E� Memorial Rd�, Oklahoma City, OK 73114�
This Jasco product comes with a 1-year limited warranty�
Visit www�byjasco�com for warranty details�
Questions? Contact us at 1-800-654-8483 between 7:00AM—8:00PM CST�
Corrective Action
• Battery may be installed incorrectly� Reinstall battery�
• Battery may need to be replaced�
Install new CR2032 battery�
• Make sure light is turned on and light bulb is working
• Receiver may have become un-paired� Pair remote
to receiver — see pairing section of manual�
• Verify that the arrows on the back of the wallplate
bracket and the remote mount line up�
• Use ¼" drill bit and drill indentations into
drywall where the screws touch the wall�
36240 V1
03/30/17 RT