Skil GT1-0540 Serie Manual Original página 18

- if an increasing oil pattern developes, the automatic
oiler is operating fine
- if there is no oil pattern, despite a full oil reservoir, see
"TROUBLESHOOTING" or contact your dealer
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
! before returning, the oil reservoir must be
completely emptied
• Be aware that damage due to overload or improper
handling of the tool will be excluded from the warranty
(for the SKIL warranty conditions see www.skil.com or
ask your dealer)
• Storage p
- if the chain saw is to be stored for a longer period of
time, clean chain and chain bar
- when storing tool, the oil reservoir must be completely
emptied
- use chain guard X when storing the tool
- securely mount storage rail Y on the wall with 2 screws
(not supplied) and horizontally leveled
- make sure that hook Z is mounted together with rail Y
- store the tool by hanging it on the storage hook Z
- be aware of oil leakage when using storage hook Z
- store the tool indoors in a dry and locked-up place, out
of reach of children
TROUBLESHOOTING
• The following listing shows problem symptoms, possible
causes and corrective actions (if these do not identify
and correct the problem, contact your dealer or service
station)
! in case of electrical or mechanical malfunction,
immediately switch off the tool and remove battery
Tool does not operate

- kickback brake is activated -> pull hand guard S 2
back in position
- empty battery -> charge battery
- hot battery -> let battery cool down
- internal fault -> contact dealer/service station
Tool operates intermittently

- internal wiring defective -> contact dealer/service
station
- on/off switch defective -> contact dealer/service station
Dry chain

- no oil in reservoir -> refill oil
- vent in oil reservoir cap clogged -> clean cap
- oil passage clogged -> clean oil passage outlet
Brake does not stop chain

- kickback brake/run-down brake defective -> contact
dealer/service station
Chain/chain bar overheats

- no oil in reservoir -> refill oil
- vent in oil reservoir cap clogged -> clean cap
- oil passage clogged -> clean oil passage outlet
- chain is overtensioned -> adjust chain tension
- dull chain -> sharpen chain or replace
Tool vibrates abnormally

- chain tension too loose -> adjust chain tension
- dull chain -> sharpen chain or replace
- chain worn out -> replace chain
- chain teeth are facing in the wrong direction ->
reassemble with chain in correct direction
ENVIRONMENT
• Do not dispose of electric tools, batteries,
accessories and packaging together with household
waste material (only for EU countries)
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 6 will remind you of this when the need for
disposing occurs
NOISE / VIBRATION
• Measured in accordance with EN 60745 the sound
pressure level of this tool is 80.6 dB(A) and the sound
power level 100.6 dB(A) (uncertainty K = 1.87 dB), and
the vibration 5.5 m/s² (triax vector sum; uncertainty
K = 1.5 m/s²)
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60745;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
b
Tronçonneuse sans fil à moteur
sans balai
INTRODUCTION
• L'outil électrique est conçu pour scier le bois, comme par
ex. les poutres en bois, les planches, les branches, les
tronçons ainsi que pour abattre des arbres; il peut être
utilisé pour des coupes dans et contre le sens des fibres
du bois
• Cet outil n'est pas conçu pour un usage professionnel
• Vérifiez que le conditionnement contient toutes les
pièces présentées dans le schéma 2
• Lorsque des pièces manquent ou sont endommagées,
veuillez contacter votre distributeur
• Lisez et conservez ce manuel d'instruction 3
• Prêtez attention aux consignes de sécurité et aux
avertissements; ne pas suivre ces instructions peut
entraîner des graves blessures
18
0540