Technical Specification - CTEK MXTS 70 Manual De Usuario

TEChNICAL SPECIFICATION

Charger model MXTS 70
Model number 1045
Rated Voltage AC 220–240VAC, 50–60Hz
Charging voltage Max 16V/32V
Start voltage 2.0V
Output current Max 70A/35A (max 30 sec.)
Max continuous 50A/25A
Current, mains 6.3–4.4A rms (at full charging current)
Back current drain* <1Ah/month
Ripple** <4%
Ambient -20°C to +50°C
temperature (-4°F to +122°F)
Charger type 8 step, fully automatic charging cycle with
adjustable parameters
Battery types All types of 12V/24V lead-acid batteries
(WET, MF, Ca/Ca, AGM and GEL)
Battery capacity 12V: 40–1500Ah, 24V: 20–750Ah
Dimensions 332 x 178 x 80mm (L x W x H)
Insulation class IP20
Weight 3.6kg (without charger cable)
*) Back current drain is the current that drains the battery if the charger is not connected
to the mains. CTEK chargers has a very low back current.
**) The quality of the charging voltage and charging current is very important.
A high current ripple heats up the battery which has an aging effect on the positive
electrode. High voltage ripple could harm other equipment that is connected to the
battery. CTEK battery chargers produce very clean voltage and current with low ripple.
LIMITED WARRANTy
CTEK SWEDEN AB, issues this limited warranty to the original purchaser of
this product. This limited warranty is not transferable. The warranty applies
to manufacturing faults and material defects for 2 years from the date of
purchase. The customer must return the product together with the receipt of
purchase to the point of purchase. This warranty is void if the battery charger
has been opened, handled carelessly or repaired by anyone other than
CTEK SWEDEN AB or its authorised representatives. The charger is sealed.
Removing or damaging the seal will void the warranty. CTEK SWEDEN AB
makes no warranty other than this limited warranty and is not liable for
any other costs other than those mentioned above, i.e. no consequential
damages. Moreover, CTEK SWEDEN AB is not obligated to any other
warranty other than this warranty.
8 • EN
SAFETy
• The charger is designed for charging 12V lead-acid batteries
40–1500Ah or 24V batteries 20–750Ah. Do not use the charger for any
other purpose.
• Check the charger cables prior to use. Ensure that no cracks have
occurred in the cables or in the bend protection. A charger with damaged
cables must not be used. A damaged cable must be replaced.
• Never charge a damaged battery.
• Never charge a frozen battery.
• Never place the charger on top of the battery when charging.
• Always provide for proper ventilation during charging.
• Avoid covering the charger.
• A battery being charged could emit explosive gasses. Prevent sparks
close to the battery. When batteries are reaching the end of their lifecycle
internal sparks may occur.
• All batteries fail sooner or later. A battery that fails during charging
is normally taken care of by the chargers advanced control, but some
rare errors in the battery could still exist. Don't leave any battery during
charging unattended for a longer period of time.
• Ensure that the cabling does not jam or comes into contact with hot
surfaces or sharp edges.
• Battery acid is corrosive. Rinse immediately with water if acid comes
into contact with skin or eyes, seek immediate medical advice.
• Always check that the charger has switched to STEP 7 before leaving
the charger unattended and connected for long periods. If the charger has
not switched to STEP 7 within 55 hours, this is an indication of an error.
Manually disconnect the charger.
• Batteries consume water during use and charging. For batteries
where water can be added, the water level should be checked regularly.
If the water level is low add distilled water.
• This appliance is not designed for use by young children or people
who cannot read or understand the manual unless they are under the
supervision of a responsible person to ensure that they can use the battery
charger safely. Store and use the battery charger out of the reach of
children, and ensure that children cannot play with the charger.
• Connection to the mains supply must be in accordance with the
national regulations for electrical installations.
• The charger must only be connected to an earthed socket outlet.
• The charger is designed for indoor use. Do not expose to rain or snow.
CTEK prodUCTS ArE proTECTEd by
patents designs
EP1618643 RCD 000509617
SE525604 US D571179
US7541778B2 US D575225
EP1744432 pending US D581356
EP1483817 pending US D580853
SE524203 RCD 321216
US7005832B2 RCD 200830199948X pending
EP1716626 pending RCD 000911839
SE526631 RCD 081418
US-2006-0009160-A1 pending US D29/319135 pending
EP1903658 pending RCD 001119911
EP1483818 RCD 321197
US7629774 RCD 321198
SE528232 RCD 200830120183.6 pending
EP09170640.8 pending ZL200830120184.0
US12/564360 pending RCD 000835541
EP09180286.8 pending US D596125
US12/646405 pending US D596126
SUPPORT
CTEK offers a professional customer support: www.ctek.com.
For latest revised user manual see www.ctek.com.
By e-mail: info@ctek.se,
by telephone: +46(0) 225 351 80, by fax +46(0) 225 351 95.
By mail: CTEK SWEDEN AB, Rostugnsvägen 3, SE-776 70
VIKMANSHYTTAN, SWEDEN.
VIKMANSHYTTAN, SWEDEN 2010-05-01
Jarl Uggla, President
CTEK SWEDEN AB
2010-01-27
Trade marks
CTM TMA669987
CTM 844303
CTM 372715
CTM 3151800
CTM 405811
CTM 1461716 pending