Polk Audio Atrium 5c Manual Del Usuario página 6

Architectural Specifications
The loudspeaker shall consist of a 127mm
(5") low-frequency transducer, 19mm (3/4")
high-frequency transducer, and a frequency
dividing network (70V/100V transformer with
tap settings) installed in a sealed enclosure.
The low-frequency voice coil shall be 25 mm
(1") in diameter.
Performance specifications of a typical
production unit shall be as follows:
Usable frequency response shall extend from
60 Hz to 20 kHz (10dB below rated sensitivity,
in full-space, with no external equalization).
The loudspeaker shall be equipped with
a transformer for use in either 70V or 100V
distributed-line sound systems with five (5)
taps selectable by rotary switch. The taps
shall be nominally normal pass-through
for standard 8 Ohm operation:
100V Line: Tap1 = Pass through,
Tap 2 = 15 W, Tap 3 = 30 W,
Tap 4 = 60 W, Tap 5 is not used
70V Line: Tap1 = Pass through,
Tap 2 = 7.5 W, Tap 3 =15 W,
Tap 4 = 30 W, Tap 5 = 60 W
The frequency dividing network shall have
a crossover frequency of 2.5 kHz. Rated power
capacity of the components and network
shall be at least 100 W continuous program
power, defined as 3dB above a test signal
of filtered random noise conforming to
international standard IEC268-5 (shaped
pink noise with a peak-to-average ratio
of 6dB), for 100 continuous hours duration.
The system shall be protected against damage
from occasional over-powering via full range
series lamp and an automatic resettable fuse
(poly switch) that limits the power to the
network and transducers. The high frequency
transducer shall have a dispersion pattern that
can cover a 90° horizontal by 90° vertical area.
10 Polk Audio Customer Service 800-377-7655 (Outside USA & Canada: 410-358-3600)
The enclosure shall be constructed of high-
impact mineral-filled polypropylene for
protection against the elements in outdoor
applications, and for paintability.
The grille shall be aluminum for resistance
against rusting, it shall be powder-coated,
and shall be pressed-fit around the baffle
to keep it in place when facing downward.
The low frequency transducer shall have
a polypropylene-coated cone and a butyl rubber
surround, which shall extend seamlessly over
the edge of the speaker frame for protection
against the elements. The high frequency
transducer shall be constructed of anodized
aluminum for weather resistance.
The system shall withstand Mil Spec 810 testing
with specified time durations for exposure to
the following environments with no effect on
its acoustical performance or structural integrity:
salt spray (method 509.3), temperature -40°C
to 85°C (method 501.3 and 502.3), 95% humidity
(method 507.3) and ultra-violet (method 505.3).
The system shall have an IEC 529 splash proof
rating of IP-X4.
The loudspeaker shall be rotatable over
a minimum of ±180° via a Speed-Lock
mounting system.
The external wiring connectors shall be spring
loaded and nickel plated, and shall accept bare
wire up to 12 gauge. Overall cabinet dimensions
shall be no greater than 261.9 mm (10 5/16")
high by 171.4 mm (6 3/4") wide by 196.8mm
(7 3/4") deep and the unit shall weigh no more
than 2.8 kg (6.2 lbs).
The finish shall be a paintable black and white.
The system shall be the Polk Audio Atrium5c
with included Speed-Lock mounting system.
SPECIFICATIONS
Frequency Range (-10 dB): 60 Hz-20 kHz
Power Capacity Components and network: 100 W
continuous program transformer:
per each listed tap rating
(IEC pink noise, 100 hrs)
Tap Settings 100V Line: Tap1 = pass through
Tap 2 = 15 W
Tap 3 = 30 W
Tap 4 = 60 W
Tap 5 is not used
70V Line: Tap 1 = pass through
Tap 2 = 7.5 W
Tap 3 =15 W
Tap 4 = 30 W
Tap 5 = 60 W
LF Driver 5" (127mm) mineral-filled
polymer with rubber surround
HF Driver 3/4" (19mm) anodized aluminum
dome with rubber surround
Enclosure mineral filled polypropylene
Material
Environmental Conforms to Mil Spec 810 for humidity,
salt spray, temperature & UV.
IEC 529 IP-X4 splash-proof rating.
Polk Audio Atrium Series Speakers exceed
All-Weather baseline industrial and military
Certification specifications for environmental
endurance. Polk's own all-weather
certification goes further, so you're
assured every Atrium loudspeaker
can effortlessly withstand harsh
conditions, whether high temps
or heavy rains.
Dimensions 10 5/16" H x 6 3/4" W x 7 3/4" D
(261.9mm x 171.4 mm x 196.8 mm)
Net Weight (ea): 2.8 kg (6.2 lbs)
Shipping Weight (each): TBD
Included Speed-Lock Mounting System
Accessories
Specifications, dimensions and features subject
to change without notice. For more information
call us at 1-800-377-7655 (USA and Canada).
Outside of North America call +1 (410) 358-3600.
Customer Service Hours of Operation: Monday-Friday, 9
FIGURE 17: Tap Settings
-5:30 polkcs@polkaudio.com
AM PM EST
11