Service And Repair - Vollrath LidSaver LS01 Manual Del Operador

TROUBLESHOOTING
Note: Due to manufacturing defects, damaged lids or poorly stacking lid types, some lids may not dispense as planned. Under these rare conditions
your customer is still able to easily retrieve a lid.
Problem
Unsatisfactory dispensing
More than one lid releases when
opening door
Single lid dispenses inconsistently.
Lids are frequently damaged.
Door is disengaged from door pivots
or becomes disengaged when
opened too far.

SERVICE AND REPAIR

Serviceable parts are available on Vollrath.com.
To avoid serious injury or damage, never attempt to repair the unit or replace a damaged power cord yourself. Do not send units directly to
The Vollrath Company LLC. Please contact Vollrath Technical Services for instructions.
When contacting Vollrath Technical Services, please be ready with the item number, model number (if applicable), serial number, and proof of
purchase showing the date the unit was purchased.
WARRANTY STATEMENT FOR THE VOLLRATH CO. L.L.C.
This warranty does not apply to products purchased for personal, family or household use, and The Vollrath Company LLC does not offer a written
warranty to purchasers for such uses.
The Vollrath Company LLC warrants the products it manufactures or distributes against defects in materials and workmanship as specifically
described in our full warranty statement. In all cases, the warranty runs from the date of the end user's original purchase date found on the receipt.
Any damages from improper use, abuse, modification or damage resulting from improper packaging during return shipment for warranty repair will
not be covered under warranty.
For complete warranty information, product registration and new product announcement, visit www.vollrath.com.
www.vollrath.com
Might be Caused By
Your lid may be incorrect for your
LidSaver™ settings.
LidSaver™ may be overfilled with lids.
When lids are compressed too tightly
from overstocking they will not dispense
well. Instruct staff to not overstock lids.
Pager flipper not returning to proper
working position after loading lid stack.
Pager not securely fastened down.
Lid claw is missing or damaged.
Piston or piston spring may be damaged
and preventing movement to the most
forward position.
One or pager flappers have migrated
inward, causing the lids to be held too
firmly.
Door pivot screws are sheared.
The Vollrath Company, L.L.C.
1236 North 18th Street
Sheboygan, WI 53081-3201 U.S.A.
Main Tel: 800.624.2051 or 920.457.4851
Main Fax: 800.752.5620 or 920.459.6573
Customer Service: 800.628.0830
Canada Customer Service: 800.695.8560
Course of Action
Read label on "lid plate". If this does not match your lids, order a lid
change kit" to reset your LidSaver™ for your lid.
Remove lids and flake the stack. Avoid overstocking lids when
loading.
Using warm soapy water, thoroughly saturate pager and flipper
until flipper operates freely.
Grasp each pager to determine if it is loose and allows movement
within the adjustment slot. Order a tune-up kit to set these
components accurately.
Look for horizontal motion in one or the other claw. If horizontal
motion is noticed, tighten or replace the claw screws. If claw is
broken, order a new claw.
The piston or piston spring may be damaged. Clean the inside of
the tube
Remove housing. Inspect the lid claw/lid interaction. Move the door
to check if the lid claw reaches behind the first lid when the door is
completely closed. If the claw does not reach back far enough,
order a Lid Tune Up Kit to reset the pagers.
Remove the door pivot screws. Replace with 0.75-1.00" 10-24
round head screws.
Technical Services
techservicereps@vollrathco.com
Induction Products: 800.825.6036
Countertop Warming Products: 800.354.1970
All Other Products: 800.628.0832
©
2017 The Vollrath Company L.L.C. Part No. 8012600-1 ml 1/30/17