Troubleshooting; Importantes Mises En Garde - Black and Decker ST1000 Manual De Instrucciones

How To Use Your Black & Decker Yard Trimmer
CLIP-TO-LOCK CORD RETAINER: (UNPLUG EXTENSION CORD AT TRIMMER)
An extension cord retainer is built into the switch handle that prevents the extension cord from
pulling out of the handle. To use the retainer, double the extension cord, as shown in Figure 1,
about a foot from the female end. Depress the retainer latch, shown in the figure, and insert the
cord as far as it will go. Holding the cord in place, release the retainer latch and the cord will be
securely held. To remove the cord, depress the retainer latch and pull the cord out.
Trimming Technique and Performance Notes
Proper trimming technique is essential to obtain the maximum in performance and handling ease.
CAUTION: Inspect area to be trimmed for any wire, cord, or string-like matter which could
become entangled in the rotating line or spool. Be particularly careful to avoid any wire which
might be bent outwardly into the path of the tool, such as barbs at the base of a chain link fence.
Tilt trimmer at a slight angle from the ground (Figure 2).
Lower to grass or weeds you intend to cut. (If they are over 20cm (8 in.) high, start cutting at
top.)
Slowly swing unit into and out of area being cut, holding the unit off the ground at desired
cutting height.
IMPORTANT — for the best cutting action against walls, fences and in high grass, move
trimmer slowly so grass is cut WITH THE TIP of the high speed nylon line.
1. Avoid running trimmer with hub in contact with ground.
2. Trim only when grass and weeds are dry.
3. The life of your nylon line is dependent upon following the above trimming techniques, as
well as what is being cut, and where the cutting is being done.
EXAMPLE: Line will wear faster when run against a foundation wall as compared to
trimming around a tree. Some line breakage will occur from feeding unit too fast, from
entanglement with foreign matter, from normal line fatigue, and from attempting to cut thick,
stalky weeds in excess of unitʼs capability.
NOTE: As the weather becomes cooler, the tendency for the nylon line to break becomes
greater.
DO NOT USE UNIT WHEN TEMPERATURE IS BELOW 50° F
4. For best performance, as the line wears, lengthen as indicated in Line Feeding Procedure.
5. Periodically unplug extension cord at trimmer and remove the accumulation of grass
or cutting debris from the inside of the bump cap shroud as shown in Figure 3.
Line Feeding Procedure
In order to feed a length of cutting line, strike the bump cap on the lawn while the trimmer is
running. This will automatically feed a new length of line and trim it to the correct length. A firm
but gentle motion should be used to strike the bump cap. The unit should be angled slightly
forward to prevent the guard from contacting the ground. This process may be repeated as
often as necessary. If unit fails to feed, unplug extension cord at trimmer and clean out the
bump cap (See Figure 3).
Spool Replacement and Recovery of Line Broken Off
Inside Spool
1. Unplug extension cord at trimmer.
2. Remove the bump cap by pulling up while depressing the two release tabs on the sides of
the hub at the points shown in Figure 4.
NOTE: It may be necessary to pull up on the cap while depressing the release tabs one
side at a time.
NOTE: The cutting line is quite springy and can be awkward to handle.
3. Remove any broken cutting line, wrap the remaining line tight and reinsert spool into hub as
follows.
a.Wind the line tight enough so that it is all below the edges of the flanges on the spool. If it
extends past the flanges, it wonʼt fit into the hub.
b.Place the loose end of the cutting line through the gap in the spool flange as shown in
Figure 6. (Either gap will do but try to leave yourself about 3 or 4 inches of line to work
with as shown in the figure 5)
c. Holding the line in the gap, insert the end through the eyelet in the hub and slip the spool
into the hub, as shown in Figure 6.
Make sure the spring is still in place in the hub. If the spool does not slip into the hub easily,
press gently and pull straight out on the cutting line that protrudes through the eyelet.
4. Once the spool drops into the hub, align the release tabs on the shroud with the slots in
the hub and press the shroud into place. Be sure that both release tabs snap into place.
5. To replace the line on a spool, follow the steps below
a.Locate, on the empty spool, one of the two small holes shown in Figure 7.
b.Insert the end of the line no more than 1/8 in. into the hole and begin winding the line
around the spool. Be sure to wind the line in the direction of the arrow in Figure 8.
c.Perform steps 4 and 5.
Maintenance- Unplug Extension Cord at Trimmer
MAINTAIN TOOL WITH CARE
1. Keep the air intake slots clean to avoid overheating which will damage trimmer. For this
cleaning, use a dry brush or cloth to remove grass, sap or other debris.
2. Plastic parts may be cleaned by using a mild soap and a rag dampened with hot water.
Avoid all other types of detergents, cleaners or solvents which might contain chemicals that
could seriously damage the plastic. Do not spray the trimmer with water.
3. Self lubricating bearings are used in the tool and periodic relubrication is not required.
However, it is recommended that after two or three seasons of use, you take or send the
trimmer to a Black & Decker service center or authorized service station (see TOOLS,
ELECTRIC in yellow pages) for a thorough cleaning, inspection and relubrication. If the tool
is being used professionally, the above should be accomplished after each trimming season.
4. If trimmer fails to operate, disconnect extension cord from power source first, then from
trimmer. Make sure extension cord is undamaged and that house fuses are not blown or
circuit breakers tripped. If trimmer still fails to operate, take or send it to your local B&D
service center or authorized service station for repair. Do not attempt to repair it yourself.
IMPORTANT
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement) should be performed by Black & Decker
service centers or other qualified service organizations, always using Black & Decker
replacement parts. When servicing use ONLY IDENTICAL REPLACEMENT PARTS.
Accessories
Replacement line and safety spectacles are available from your local dealer, or a Black &
Decker service center.If you need assistance in locating any accessory, please contact:
Black & Decker (U.S.) Inc., Consumer Service Department,
626 Hanover Pike, P.O. Box 618, Hampstead, MD 21074-0618.
Recommended accessories for your trimmer are shown in this manual. The use of any other
accessory or attachment might be hazardous.
Cat. No. RS-136, (82-136-02) Replacement Spool with 20 feet of Nylon Line.
Cat. No. BL-065, (82-602) Hank of bulk .065 in. dia. Nylon Line (50 feet)
Cat. No. 82-611 One pound .065 in. dia. Nylon Line.
CAUTION: Use only accessories with your yard trimmer. The use of any other
recommended
attachment or accessory might be hazardous. Use only specially treated .065 in. diameter
Black & Decker monofilament nylon line with your yard trimmer.

TROUBLESHOOTING

Problem Possible Cause
• Unit will not start. • Cord not plugged in.
• Circuit fuse is blown.
• Circuit breaker is tripped. • Reset circuit breaker. (If the product
• Cord or switch is
damaged.
For assistance with your product, visit our website www.blackanddecker.com for the
location of the service center nearest you or call the BLACK & DECKER help line at
1-800-544-6986.
Possible Solution
• Plug tool into a working outlet.
• Replace circuit fuse. (If the product
repeatedly causes the circuit fuse to
blow, discontinue use immediately and
have it serviced at a Black & Decker
service center or authorized servicer.)
repeatedly causes the circuit breaker to
trip, discontinue use immediately and
have it serviced at a Black & Decker
service center or authorized servicer.)
• Have cord or switch replaced at Black
& Decker Service Center or Authorized
Servicer
NOTE: Always include date code numbers on all correspondence. This 4 or 5 digit number is
printed on the nameplate label located on the motor housing.
SERVICE INFORMATION
All Black & Decker Service Centers are staffed with trained personnel to provide customers
with efficient and reliable power tool service. Whether you need technical advice, repair, or
genuine factory replacement parts, contact the Black & Decker location nearest you. To find
your local service location, refer to the yellow page directory under "Tools—Electric" or call:
1-800-544-6986 or visit www.blackanddecker.com
FULL TWO-YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material
or workmanship. The defective product will be replaced or repaired at no charge in either of
two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom
it was purchased (provided that the store is a participating retailer). Returns should be made
within the time period of the retailerʼs policy for exchanges (usually 30 to 90 days after the
sale). Proof of purchase may be required. Please check with the retailer for their specific
return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or
authorized Service Center for repair or replacement at our option. Proof of purchase may be
required.Black & Decker owned and authorized Service Centers are listed under
"Tools-Electric" in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights and
you may have other rights which vary from state to state or province to province. Should you
have any questions, contact the manager of your nearest Black & Decker Service Center.
This product is not intended for commercial use.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are
missing, call 1-800-544-6986 for a free replacement.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For
products sold in Latin America, check country specific warranty information contained in the
packaging, call the local company or see the website for warranty information.
Imported by
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
MODE D'EMPLOI
N° de catalogue :
Merci d'avoir choisi Black & Decker!
Consulter le site Web
www.BlackandDecker.com/NewOwner
pour enregistrer votre nouveau produit.
À LIRE AVANT DE RETOURNER CE PRODUIT
POUR QUELQUE RAISON QUE CE SOIT :
Si des questions ou des problèmes surgissent après l'achat d'un produit Black & Decker,
consulter le site Web
HTTP://WWW.BLACKANDDECKER.COM/INSTANTANSWERS
pour obtenir des réponses instantanément 24 heures par jour.
Si la réponse est introuvable ou en l'absence d'accès à Internet, composer le
1-800-544-6986 de 8 h à 17 h HNE, du lundi au vendredi, pour parler avec un agent.
Prière d'avoir le numéro de catalogue sous la main lors de l'appel.

IMPORTANTES MISES EN GARDE

AVERTISSEMENT :
électriques ou de blessures lorsquʼon utilise des outils électriques, il faut toujours respecter les
mesures de sécurité suivantes.
AVERTISSEMENT :
fermer des produits chimiques. Selon lʼétat de la Californie, ces produits chimiques peuvent
causer le cancer ainsi que des malformations congénitales, et ils présentent dʼautres dan-
gers au système reproductif humain. Voici des exemples de tels produits chimiques :
• les composés dʼengrais;
• les composés dʼinsecticides, dʼherbicides et de pesticides;
• lʼarsenic et le chrome provenant de bois traité.
Afin de minimiser les risques, porter de lʼéquipement de sécurité approuvé comme des
masques antipoussières spécialement conçu pour filtrer les particules microscopiques.
AVERTISSEMENT :
du plomb. Selon lʼétat de la Californie, ce produit chimique peut causer le cancer ainsi que
des malformations congénitales, et il présente dʼautres dangers au système reproductif
humain. Se laver les mains après lʼutilisation.
MISE EN GARDE : Porter un dispositif approprié de protection de lʼouïe lors de lʼutilisa-
tion du produit. Dans certaines conditions et durées dʼutilisation, le produit peut émettre un
niveau de bruit provoquant la perte de lʼouïe.
LIRE TOUTES LES DIRECTIVES.
1. Toujours porter des LUNETTES DE SÉCURITÉ. Les porter tant et aussi longtemps que
lʼappareil est branché.
2. Ne pas utiliser lʼoutil sans le PROTECTEUR en place.
3. Éloigner en tout temps le visage, les mains et les pieds du FIL DE NYLON qui tourne. Ne
pas le régler à une longueur dépassant celle qui est spécifiée dans le présent guide. Porter
des pantalons afin de se protéger les jambes.
4. ÉLOIGNER LES SPECTATEURS, surtout les enfants.
5. ÉVITER LES DÉMARRAGES ACCIDENTELS. Ne pas laisser le doigt sur lʼinterrupteur
lorsquʼon transporte un outil branché.
6. NE JAMAIS FORCER L'OUTIL. Afin dʼobtenir un rendement sûr et efficace, utiliser lʼoutil à
son rendement nominal.
7. UTILISER L'OUTIL APPROPRIÉ. Se servir de lʼoutil selon lʼusage prévu.
8. NE PAS DÉPASSER SA PORTÉE. Toujours demeurer dans une position stable et garder
son équilibre.
9. AVERTISSEMENT : Afin dʼéviter les risques de secousses électriques, utiliser lʼoutil
seulement avec un cordon de rallonge conçu pour lʼextérieur. Toujours brancher le cordon de
rallonge sur une ligne pourvue de fusibles ou protégée par un disjoncteur.
10.NE PAS MANIPULER LE CORDON DE FAÇON ABUSIVE. Ne pas tirer sur le cordon pour le
débrancher de la prise. Tenir le cordon loin des sources de chaleur, des flaques dʼhuile et
des arêtes tranchantes.
11.Afin dʼéviter le débranchement accidentel du CORDON DE RALLONGE pendant lʼutilisation,
se servir du dispositif de retenue du cordon de la façon décrite dans le présent guide.
12.POUR ÉVITER D'ENDOMMAGER L'OUTIL, lʼarrêter immédiatement lorsquʼil frappe un objet
ou quʼil sʼenchevêtre dans un corps étranger. Débrancher lʼoutil, vérifier sʼil est endommagé
et le faire réparer avant de sʼen servir de nouveau. Ne pas sʼen servir lorsque la bobine ou le
moyeu sont endommagés.
13.POUR ÉVITER D'ENDOMMAGER LE CORDON, lʼéloigner du fil qui tourne. En cas de dom-
mage, débrancher le cordon de la prise avant de déplacer lʼoutil ou dʼexaminer lʼétendue des
dommages. Remplacer le cordon endommagé.
14.DÉBRANCHER L'OUTIL lorsquʼil ne sert pas et avant de remplacer la bobine ou de nettoyer
le moyeu.
15.PORTER DES VÊTEMENTS APPROPRIÉS. Ne jamais utiliser lʼoutil lorsquʼon est pieds nus
ou que lʼon porte des sandales. Toujours porter des chaussures fermées. Il est recommandé
de porter des gants de caoutchouc et des chaussures à semelle antidérapante pour travailler
à lʼextérieur.
16.ÉVITER LES MILIEUX DE TRAVAIL DANGEREUX. Ne pas utiliser lʼoutil dans des endroits
See 'Tools-Electric'
– Yellow Pages –
for Service & Sales
ST1000
Afin de réduire les risques dʼincendie, de secousses
Le produit génère de la poussière qui peut ren-
Le produit renferme des produits chimiques, dont