Troubleshooting; Protecting The Environment; Technical Data - Black and Decker BDHT185ST1 Manual De Instrucciones

Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
u
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
u
switch off.
Unplug the charger before cleaning it. Your charger does
u
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your appliance/tool/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
After use, carefully clean the blades. After cleaning, apply
u
a film of light machine oil to prevent the blades from rust-
ing.
The cutting blades are made from high quality, hardened steel
and with normal usage, they will not require resharpening.
However, if you accidentally hit a wire fence, stones, glass or
other hard objects, you may put a nick in the blade. There is
no need to remove this nick as long as it does not interfere
with the movement of the blade.
If it does interfere, remove the battery and use a fine toothed
file or sharpening stone to remove the nick. If you drop the
trimmer, carefully inspect it for damage. If the blade is bent,
housing cracked, or handles broken or if you see any other
condition that may affect the trimmer's operation contact your
local BLACK+DECKER Service Center for repairs before
putting it back into use. Fertilizers and other garden chemicals
contain agents which greatly accelerate the corrosion of
metals. Do not store the unit on or adjacent to fertilizers or
chemicals. With the battery removed, use only mild soap and
a damp cloth to clean the unit. Never let any liquid get inside
the unit; never immerse any part of the unit into a liquid. Pre-
vent the blades from rusting by applying a film of light machine
oil after cleaning.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
u
plug.
Connect the blue lead to the neutral terminal.
u
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.

Troubleshooting

Problem Possible Cause
Slow running, Dry, corroded blades.
noisy or hot
blades.
Blade or blade support
bent.
Bent or damaged teeth.
Loose blade bolts.
Possible Solution
Lubricate blades.
Straighten blade or blade
support.
Straighten teeth.
Tighten blade bolts.
(Original instructions)
Troubleshooting
Unit will not Battery not installed
start. properly.
Battery not charged.
Lock off not fully
operated.
Battery won't Battery not inserted into
charge charger.
Charger not plugged in.
Surrounding air
temperature too hot or
too cold.

Protecting the environment

Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions.

Technical data

Input Voltage
Blade strokes (no load) min-1
Blade length
Blade gap
Weight
Battery
Voltage
Capacity
Type
Charger
Input Voltage
Output Voltage
Current
ENGLISH
Check battery installation.
Check battery charging require-
ments.
Check lock off is fully depressed
prior to moving main trigger.
Insert battery into charger until
green LED appears. Charge
up to 8 hours if battery totally
drained.
Plug charger into a working out-
let. Refer to "Important Charging
Notes" for more details. Check
current at receptacle by plugging
in a lamp or other appliance.
Check to see if receptacle is
connected to a light switch which
turns power off when you turn
out the light.
Move charger and tool to a
surrounding air temperature of
above 40 degree F (4.5°C) or
below 105 degree F (+40.5°C).
BDHT185ST1, BDHT185L1 (H2)
V
DC
cm
mm
kg
V
DC
Ah
906068**
V
AC
V
DC
mA
18
2600
50
18
2.8
BL2518
18
2.5
Li-Ion
230
18
2000
9