Display; Factory Reset; Exit Menu; Error Messages - Danfoss 088L5130 Manual Del Usuario

Programmable Thermostats 088L5130/5132

Display

I want to choose the information to be shown on the
thermostat display.
To do so, you must:
1 Press the OK button twice to activate the menu.
2 Press the Up or Down buttons until the Settings option
fl ashes.
3 Press the OK button.
4 Press the Up or Down buttons until the Display option
fl ashes.
5 Press the Up or Down buttons to select whether or you wish to:
- display the Clock or not (On/Off),
- display the Set temperature or not (On/Off).
You can also decide whether the temperature displayed is:
- the Room temperature,
- the Floor temperature (if a fl oor sensor is used), or
- the Regulator temperature.
6 Press the OK button to confi rm the settings as you work your
way through the various options in the Display submenu.
7 Select Exit to exit the option.
Factory settings:
- TIME: ON
- Set temp.: ON
- Floor temperature is shown
FLOOR
TIME
DAY
CHILDLOCK
SETTINGS C°/F°
APPLICATION
OFFSET TEMP
READOUT
ADAPTIVE
DISPLAY

FACTORY RESET

EXIT
Factory Reset
I want to return to the factory settings.
To do so, you must:
1 Press the OK button twice to activate the menu.
2 Press the Up or Down buttons until the Settings option
fl ashes.
3 Press the OK button.
4 Press the Up or Down buttons until the Factory Reset option
fl ashes.
5 Press the OK button. A submenu will appears.
6 Press the Up or Down buttons until the Reset option fl ashes.
7 Press the OK button.
8 Select Exit to exit the option.
TIME
DAY
CHILDLOCK
SETTINGS C°/F°
APPLICATION
OFFSET TEMP
READOUT
ADAPTIVE
DISPLAY
FACTORY RESET
EXIT
6
Room/fl oor/regulator
On/Off
On/Off
RESET
EXIT

Exit Menu

I want to exit a menu.
To do so, you must use the Exit option:
The various menus and submenus contain an Exit option.
1 Press the Up or Down buttons until Exit fl ashes.
2 Press the OK button. You may have to repeat steps 1 and 2 to
return to the fi nal Exit option.
Please note: When you activate a menu, the menu item last se-
lected will begin fl ashing. This allows you to view the latest setting.
If, for example, you activate the Mode menu, Man. mode will fl ash
if you used Man. mode the last time.
This principle also applies to current temperature/time settings.
When you enter the various menus, they always display the value
that was last selected. This allows you to check the current set-
tings.
Should you enter a menu by mistake, you can exit it again without
changing the setting by simply confi rming the current setting, i.e.
by clicking the OK button.

Error Messages

E0 = Internal failure. Replace thermostat.
E1 = Air sensor defective or short-circuited. Replace thermostat.
E2 = Floor sensor defective or short-circuited. Check fl oor sensor.
Factory Settings for Automatic 5:2 Program
Event Time
Morning 6:00 a.m. - 8:00 a.m.
Out 8:00 a.m. - 4:00 p.m.
Home 4:00 p.m. - 10:00 p.m.
Night 10:00 p.m. - 6:00 a.m.
Days 6-7 (Saturday - Sunday)
Event Time
Day 8:00 a.m. - 11:00 p.m.
Night 23:00 p.m. - 08:00 a.m.
© 2009 Danfoss Inc.
Days 1-5 (Monday - Friday)
English
Temperature
77°F / 25°C
68°F / 20°C
77°F / 25°C
68°F / 20°C
Temperature
77°F / 25°C
68°F / 20°C