AVS Electronics OUTSPIDER PA Manual Del Usuario página 22
Ocultar thumbs
Ver también para OUTSPIDER PA:
- Manual de instrucciones (136 páginas) ,
- Manual de instrucciones (150 páginas)
Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
OUTSPIDER PA address
For OUSPIDER PA model used with serial connections (DIP 1 of SW2 in OFF), the
DIP SWITCHES from 1 to 5 at the desk SW1 are used to assign an address to the
sensor.
However, it is also possible to use the DIP SWITCHES of SW 1 momentarily in PC/
BUS mode to configure the two sections as if the DIP/RELE' mode was selected.
To do so, simply:
S
W
1
-
S
E
N
S
e
n
s
r o
D
P I
1
D
P I
2
D
P I
3
D
P I
4
D
P I
1
O
N
O
N
O
N
O
N
O
2
O
F
F
O
N
O
N
O
N
O
3
O
N
O
F
F
O
N
O
N
O
4
O
F
F
O
F
F
O
N
O
N
O
5
O
N
O
N
O
F
F
O
N
O
6
O
F
F
O
N
O
F
F
O
N
O
7
O
N
O
F
F
O
F
F
O
N
O
8
O
F
F
O
F
F
O
F
F
O
N
O
9
O
N
O
N
O
N
O
F
F
O
1
0
O
F
F
O
N
O
N
O
F
F
O
1
1
O
N
O
F
F
O
N
O
F
F
O
1
2
O
F
F
O
F
F
O
N
O
F
F
O
1
3
O
N
O
N
O
F
F
O
F
F
O
1
4
O
F
F
O
N
O
F
F
O
F
F
O
1
5
O
N
O
F
F
O
F
F
O
F
F
O
1
6
O
F
F
O
F
F
O
F
F
O
F
F
O
1. Set the DIP SWITCH according to the desired configuration.
2. Put DIP SWITCH 1 of SW 2 in the ON position.
3. Bring DIP SWITCH 1 of SW 2 back to the OFF position.
4. Place the DIP SWITCH of SW 1 in position according to the address that will be
assigned to the sensor.
Initial power-up
Upon initial power-up the anti-masking circuit completes a self-adjustment.
In this phase it is essential for the cover to be properly installed in order
to allow the sensor to adjust itself to the correct value.
S
O
R
A
D
D
R
E
S
S
5
S
e
n
s
r o
D
P I
1
D
P I
2
D
P I
3
D
P I
4
N
1
7
O
N
O
N
O
N
O
N
N
1
8
O
F
F
O
N
O
N
O
N
1
9
N
O
N
O
F
F
O
N
O
N
N
2
0
O
F
F
O
F
F
O
N
O
N
2
1
N
O
N
O
N
O
F
F
O
N
N
2
2
O
F
F
O
N
O
F
F
O
N
N
2
3
O
N
O
F
F
O
F
F
O
N
N
2
4
O
F
F
O
F
F
O
F
F
O
N
N
2
5
O
N
O
N
O
N
O
F
F
2
6
N
O
F
F
O
N
O
N
O
F
F
N
2
7
O
N
O
F
F
O
N
O
F
F
2
8
N
O
F
F
O
F
F
O
N
O
F
F
N
2
9
O
N
O
N
O
F
F
O
F
F
N
3
0
O
F
F
O
N
O
F
F
O
F
F
N
3
1
O
N
O
F
F
O
F
F
O
F
F
N
3
2
O
F
F
O
F
F
O
F
F
O
F
F
Antimask and Dirty Lenses
All models OutSpider are equipped with an anti-masking circuit, made of a central RX receives
and four active infrared TX transmitters positioned on the sides of the PIR sensors, that detects
obstacles placed in front of the sensor up to a distance of about 5 cm.
An alarm, caused by an attempt to mask the sensor, is signalled by quick flashing of the yellow
sensor and activates the dedicated relay output AM.
Operation
TX
TX
D
P I
5
O
F
F
O
F
F
RX
O
F
F
O
F
F
O
F
F
O
F
F
O
F
F
TX
TX
O
F
F
O
F
F
Dirty lenses (OUTSPIDER PA only) : When the Antimask circuit detects that the average of the
O
F
F
signal value saved after a certain interval of time changes by about 20 %, the F output and the
yellow LED flashes slowly.
O
F
F
O
F
F
In order to restore the "dirty lenses" indication, it is necessary – after cleaning the lenses – to
O
F
F
remove and then give again supplying to the detector.
O
F
F
O
F
F
Precautions
O
F
F
w Keep the sensor lens clean from dust or other filtering material that may modify its operation.
w To enable that some potential
condensation can get out of the
detector, two drainage perforations
are predisposed on the cover in the
lower part of the housing. It is prudent
to practice these perforations.
- 22 -
Antimask: When the Antimask circuit detects an
obstacle that is less than 5 cm from the lenses, a
delay time of about 20 seconds activates before this
is signalled. If, at the end of this time, the obstacle is
not removed, the AM anti-masking relay activates and
the yellow LED flashes slowly.
Both the LED and the relay are automatically reset
after the first alarm of the sensor.
NOTE: this function however does not guarantee that
the sensor cannot be masked.
E
N
G
Publicidad
Tabla de contenido
