Friedrich SS Serie Instrucciones Para La Instalación página 5

Ocultar thumbs Ver también para SS Serie:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

STEP 8
STEP 8
OUTSIDE SUPPORT MOUNTING:
OUTSIDE SUPPORT MOUNTING:
STEP 8
STEP 8
STEP 8
OUTSIDE SUPPORT MOUNTING:
OUTSIDE SUPPORT MOUNTING: Assemble the support brackets (Item #1) to the bottom rails of the cabinet
OUTSIDE SUPPORT MOUNTING:
with four (4) 10-24 1" long screws (Item #2) and four (4) 10-24 flat nuts (Item #3). Adjust the support
brackets to bring the bottom pads in contact with the wall surface. (A 1" x 4" or 2" X 4" SP
USED BETWEEN THE W
USED BETWEEN THE WALL AND THE SUPPORT BRA
USED BETWEEN THE W
USED BETWEEN THE W
USED BETWEEN THE W
32" dia. pilot holes and secure the brackets to the wall with two (2) #12A x 2" long screws (Item #4).
Adjust the support brackets to provide an approximate 3/8" down slope toward the outside for drainage.
(See Figure D, Page 4). Tighten all screws.
NOTE:The supply air, intake air, condenser air inlets and outlets must be unobstructed to avoid recirculation
of rejected heated air.
The illustrations below show a standard frame construction installation as well as some suggested ways of
The illustrations below show a standard frame construction installation as well as some suggested ways of
The illustrations below show a standard frame construction installation as well as some suggested ways of
The illustrations below show a standard frame construction installation as well as some suggested ways of
The illustrations below show a standard frame construction installation as well as some suggested ways of
adapting the suppor
adapting the suppor
adapting the support brack
adapting the suppor
adapting the suppor
FIGURE 1
SUPPLY AIR
RETURN AIR
FIGURE 3
STONE LEDGE
ALL AND THE SUPPORT BRA
ALL AND THE SUPPORT BRA
ALL AND THE SUPPORT BRACKETS WHEN INST
ALL AND THE SUPPORT BRA
t bracket to thick walls and large stone ledges.
t brack
t brack
et to thick walls and large stone ledges.
et to thick walls and large stone ledges.
et to thick walls and large stone ledges.
t brack
et to thick walls and large stone ledges.
3/8" SLOPE
10 - 24 SCREW
DOWN
10 - 24 FLAT NUT
CONDENSOR
AIR OUTLET
CONDENSOR
AIR INLETS
#12A X 2" SHEET METAL
SCREW
1" X 4 OR 2" X 4" SPACER
BETWEEN WALL AND BRACKET
SHOULD BE USED ON ALUMINUM,
ASBESTOS OR VINYL SIDING.
3/8" SLOPE
DOWN
#12 X 2" SHEET
METAL SCREW
2" X 4" SPACER
CKETS WHEN INSTALLED ON AL
CKETS WHEN INST
CKETS WHEN INST
ALLED ON ALUMINUM OR VINYL SIDING).
ALLED ON AL
ALLED ON AL
CKETS WHEN INST
ALLED ON AL
FIGURE 2
3/8" SLOPE DOWN
CUT
HERE
DISCARD
SHADED AREA
FIGURE 4
STONE LEDGE
(A 1" x 4" or 2" X 4" SP
(A 1" x 4" or 2" X 4" SPA A A A A CER SHOULD BE
(A 1" x 4" or 2" X 4" SP
(A 1" x 4" or 2" X 4" SP
CER SHOULD BE
CER SHOULD BE
CER SHOULD BE
CER SHOULD BE
UMINUM OR VINYL SIDING).
UMINUM OR VINYL SIDING). Drill 5/
UMINUM OR VINYL SIDING).
UMINUM OR VINYL SIDING).
DIMENSION "A"
STONE LEDGE
OUTSIDE WALL
CUT TO FIT DIMENSION "A"
AND BEND DOWN TO FORM
A VERTICAL LEG.
3/8" SLOPE
DOWN
STRAIGHTEN TAB TO LAY FLAT
ALONG THE BOTTOM RAIL OF THE
SHELL.
SECURE THE LONGEST SIDE OF THE
BRACKET TO THE SHELL
ADJUST IN OR OUT TO REST
ON LEDGE.
Page 5

Publicidad

Tabla de contenido
loading

Tabla de contenido