Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
PART NUMBER FOR ORDERING
Common parts for ALL CD
and CX Grinders
1
Inlet Assembly . . . . . . . . . . . . . . . . . . . . . . .
2
Inlet Screen . . . . . . . . . . . . . . . . . . . . . . R1602-61
•
3
Inlet Seal . . . . . . . . . . . . . . . . . . . . . . . . 85H-167
Throttle Valve Kit . . . . . . . . . . . . . . . . . . . .
4
Throttle Valve Case . . . . . . . . . . . . . . . . LG1-300A
4A
Throttle Valve Spring Seat . . . . . . . . . . . LG1-592
4B
4C
Throttle Valve . . . . . . . . . . . . . . . . . . . . AG210-302
4D
Throttle Valve Seat . . . . . . . . . . . . . . . . LG1-303
5
6
Throttle Lever . . . . . . . . . . . . . . . . . . . . . . .
6A
Locking Throttle Lever Assembly
(standard equipment on models
ending in C, L, MC or ML; optional
for all others) . . . . . . . . . . . . . . . . . . . . . . . .
*
Lever Lock . . . . . . . . . . . . . . . . . . . . . . . LG1-402
*
Lock Spring . . . . . . . . . . . . . . . . . . . . . . LG1-405
*
Lock Pin . . . . . . . . . . . . . . . . . . . . . . . . . 5UT-757
7
Throttle Lever Pin . . . . . . . . . . . . . . . . . . . .
8
Throttle Valve Plunger . . . . . . . . . . . . . . . . .
9
Rear Rotor Bearing . . . . . . . . . . . . . . . . . . .
•
10
Rear Rotor Bearing Spacer (2) . . . . . . . . . .
•
11
Rear Rotor Bearing Retainer . . . . . . . . . . . .
12
Rotor
for CD300, CX300 and CD350
(3 slots) . . . . . . . . . . . . . . . . . . . . LG1-53-3
for all others (5 slots) . . . . . . . . . . LG1-53-5
•
13
Vane Packet (set of 5 Vanes) . . . . . . . . . . . .
14
Front End Plate . . . . . . . . . . . . . . . . . . . . . .
*
Not illustrated.
•
To keep downtime to a minimum, it is desirable to have on hand certain repair parts. We recommend that you stock one (pair or set) of each part indicated by a
bullet (•) for every four tools in service.
#
Always install a Locking Throttle Lever Assembly (6A) on a tool with a Low Profile Concentric Flange (19A). Do not equip a tool with a standard
non-locking Throttle Lever (6) and Low Profile Concentric Flange. This can allow the tool to continue to run if dropped or set down.
15
Front End Plate Spacer . . . . . . . . . . . . . . . .
•
16
Front Seal Cup . . . . . . . . . . . . . . . . . . . . . . .
LG1-A465A
17
Front Rotor Bearing . . . . . . . . . . . . . . . . . . .
18
Flow Ring
LG1-K300
19
High Profile Flange . . . . . . . . . . . . . . . . . . .
LG1-273
#
19A
Low Profile Concentric Flange
(for all models ending in C or MC) . . . . . . .
20
Flange Clamp . . . . . . . . . . . . . . . . . . . . . . . .
LG1-A400
21
Clamp Spacer . . . . . . . . . . . . . . . . . . . . . . . .
22
Clamp Nut . . . . . . . . . . . . . . . . . . . . . . . . . .
23
Collet Body . . . . . . . . . . . . . . . . . . . . . . . . .
61H-120
LG1-191
DG230-22
24
Collet
DG20-278
LG1-118
25
Nosepiece . . . . . . . . . . . . . . . . . . . . . . . . . . .
26
Collet Nut . . . . . . . . . . . . . . . . . . . . . . . . . . .
26A
Collet Wrench (11/16" x 7/16")
LG1-42-5
(included with all models) (2) . . . . . . . . . . .
PART NUMBER FOR ORDERING
for CD200 and CX200
(20 000 rpm) (grey) . . . . . . . . . . . LG1-103-0
for CD250 and CX250
(25 000 rpm) (brown) . . . . . . . . . LG1-103-1
for CD300 and CX300
(30 000 rpm) (khaki) . . . . . . . . . . LG1-103-2
for CD350 (32 000 rpm) (red) . . . LG1-103-3
Additional parts for
all CD collet models
Additional parts for
all collet models
6 mm (-EU models) . . . . . . . . . . DG110-700-6mm
1/4" (standard domestic) . . . . . . . DG110-700-G4
1/8" (available at extra price) . . . DG110-700-G2
DG10-65-5
LG1-23
LG1R-23
LG1-46
LG1-27
LG1-290
AG210-698A
AG210-699A
DG20-69A
Publicidad
Tabla de contenido
