Publicidad
Idiomas disponibles
Idiomas disponibles
area, away from ignition sources such as gas fired or electrical
appliances. During leak test, keep appliance away from open
flames or sparks.
Use a clean paintbrush and 50/50 soap and water solution. Use
mild soap and water. Do not use household cleaning agents.
Damage to gas train components can result. Brush soapy
solution onto all weld seams and entire valve area.
If "growing" bubbles appear, do not use or move the LP tank.
Contact LP gas supplier or your fire department.
Setup Using Optional Bulk Tank Hose And Refillable Cylinder
(Optional hose, not included with all models)
1. Make sure burner valves are off.
2. Attach hose to regulator & regulator to stove (as shown).
3. Attach hose to cylinder.
Leak Check
4. Turn the coupling nut clockwise to tighten to a full solid stop.
The regulator will seal on the back-check feature in LP tank
valve, resulting in some resistance. An additional one-half
to three quarters turn is required to complete connection.
Tighten by hand only – do not use tools.
NOTE: If you cannot complete connection, disconnect regulator
and repeat step 4. If you are still unable to complete the
connection, do not use this regulator!
• DO NOT insert any foreign objects into the valve outlet. You
may damage the valve and cause a leak. Leaking propane may
result in explosion, fire, severe personal injury, or death.
WARNING
Leak Check
Leak Check
• Never attempt to attach this appliance to the self-contained
LP gas system of a camper or trailer or motor home.
5. Open cylinder valve.
6. Perform leak check on hose to regulator, and hose to cylinder
connections with soapy water. Bubbles indicate a leak. Check
that the connection is not cross-threaded and that it is tight.
Perform another leak check. If there is still a leak, remove the
cylinder and contact the manufacturer for service and repair.
Arrow indicate areas to be checked.
7. Brush soapy solution onto indicated connections shown.
8. If "growing" bubbles appear, there is a leak. Close LP tank
valve immediately and retighten connections. If leaks cannot
be stopped, do not try to repair. Call for replacement parts.
Order new parts by giving the serial number, model number
and name of items needed to the Service Center at 1-800-
650-2433.
9. Always close LP tank valve after performing tank leak test by
turning hand wheel clockwise.
Hose Check
• Before each use, check to see if hoses are cut or worn. Replace
damaged hose assembly before using appliance. Use only
valve/ hose / regulator specified by manufacturer.
Dismantling Optional Bulk Tank Hose and Refillable Cylinder
1. Before dismantling high pressure hose, be sure gas pressure
in hose is eliminated.
2. Ignite stove and turn off gas valve on cylinder.
3. Allow flame to self-extinguish.
4. When flame is out, close valve on the appliance.
5. Remove hose.
Setup Instructions:
• Setup the oven on a level surface.
• Open the lid and attach the windscreens to the side of the
oven as shown.
• Make sure the pot grate is installed properly with the wire
ends fitting into the holes on the top of the oven to prevent the
rack from moving (See Picture)
Lighting Stove Instructions:
Do NOT lean over the Oven while lighting.
1. Remove all appliances from the burner to create a free flow
or air.
2. Open lid - Do not attempt to light the stove with the lid
closed.
3. Fully open LP bottle valve if using a bulk tank.
4. Turn control valve slowly to the High position. Cooker will
ignite. Adjust controls to desired temperature.
5. If ignition does not occur in 5 seconds, turn the burner
control(s) off, wait 5 minutes, and repeat lighting procedure.
If built-in ignitor will not light follow the preceding steps
and hold a lit long igniter or match next to the burner when
7
Publicidad
