B B E E F F O O R R E E R R E E Q Q U U E E S S T T I I N N G G S S E E R R V V I I C C E E
Review this chart to find do-it-yourself solutions for minor performance problems.
W W A A R R N N I I N N G G
D D i i s s c c o o n n n n e e c c t t e e l l e e c c t t r r i i c c a a l l s s u u p p p p l l y y b b e e f f o o r r e e s s e e r r v v i i c c i i n n g g o o r r c c l l e e a a n n i i n n g g t t h h e e u u n n i i t t . . F F a a i i l l u u r r e e
t t o o d d o o s s o o c c o o u u l l d d r r e e s s u u l l t t i i n n e e l l e e c c t t r r i i c c a a l l s s h h o o c c k k o o r r p p e e r r s s o o n n a a l l i i n n j j u u r r y y . .
P P R R O O B B L L E E M M
C C l l e e a a n n e e r r w w o o n n ' ' t t s s t t a a r r t t . .
P P o o o o r r j j o o b b o o f f d d i i r r t t
p p i i c c k k - - u u p p . .
C C l l e e a a n n e e r r s s t t a a r r t t s s b b u u t t
c c u u t t s s o o f f f f . .
P P O O W W E E R R N N O O Z Z Z Z L L E E w w i i l l l l n n o o t t
r r u u n n w w h h e e n n a a t t t t a a c c h h e e d d . .
C C l l e e a a n n e e r r p p i i c c k k s s u u p p m m o o v v e e a a b b l l e e
r r u u g g s s - - o o r r - - P P O O W W E E R R N N O O Z Z Z Z L L E E
p p u u s s h h e e s s t t o o o o h h a a r r d d . .
L L i i g g h h t t w w o o n n ' ' t t w w o o r r k k . .
C C o o r r d d w w o o n n ' ' t t r r e e w w i i n n d d . .
C C l l e e a a n n e e r r l l e e a a v v e e s s m m a a r r k k s s
o o n n c c a a r r p p e e t t . .
E E l l e e c c t t r r i i c c a a l l S S h h o o c c k k H H a a z z a a r r d d
P P O O S S S S I I B B L L E E C C A A U U S S E E
1 1 . . Unplugged at wall outlet.
2 2 . . Tripped circuit breaker/blown fuse
at household service panel.
3 3 . . Loose hose electrical connections.
4 4 . . Tripped overload protector in
POWER NOZZLE.
1 1 . . Full or clogged dust bag.
2 2 . . Clogged airflow passages.
3 3 . . Dirty motor safety filter.
4 4 . . Wrong pile height setting.
5 5 . . Open suction control.
6 6 . . Hole in hose.
7 7 . . Worn POWER NOZZLE brushes.
8 8 . . Worn or broken belt.
9 9 . . Dirty brush or brush supports.
1 1 0 0 . . Canister hood open.
1 1 . . Hose or hood electrical connections.
2 2 . . Tripped overload protector in
POWER NOZZLE.
3 3 . . Tripped overload protector
in canister.
1 1 . . POWER NOZZLE connections
unplugged.
2 2 . . Worn or broken belt.
3 3 . . Dirty brush or brush supports.
4 4 . . Tripped overload protector in
POWER NOZZLE.
1 1 . . Wrong pile height setting.
2 2 . . Suction too strong.
1 1 . . Burned out light bulb.
1 1 . . Dirty power cord.
2 2 . . Cord jammed.
1 1 . . Wrong vacuuming pattern.
P P O O S S S S I I B B L L E E S S O O L L U U T T I I O O N N
1 1 . . Plug in firmly, push ON/OFF switch to ON.
2 2 . . Reset circuit breaker or replace fuse.
3 3 . . Reconnect hose ends, (page 16).
4 4 . . Clean brush and brush supports,
then reset, (pages 38).
1 1 . . Change bag, (page 32).
2 2 . . Clear airflow passages, (page 44).
3 3 . . Clean filter, (page 34).
4 4 . . Adjust setting, (page 24).
5 5 . . Adjust control, (page 20).
6 6 . . Replace hose.
7 7 . . Change brushes, (page 42).
8 8 & & 9 9 . . See "Removing Belt" and"Replacing Belt"
(pages 38, 40).
1 1 0 0 . . Close and latch hood.
1 1 . . Check connections, reconnect hose
ends, (page 16).
2 2 . . Remove any items that may be caught
or jammed, then reset. If cleaner starts
and stops again, clean brush and brush
supports, then reset, (page 18).
3 3 . . Change dust bag, clear airflow blockage,
(page 44). Wait 20 minutes for motor
to cool and automatically reset.
1 1 . . Plug in firmly, (page 14).
2 2 & & 3 3 . . See "Removing Belt" and"Replacing Belt"
(pages 38, 40).
4 4 . . Check brush area for excessive lint
build-up or jamming. Clean brush and
brush supports, then reset, (page 18).
1 1 . . Adjust setting, (page 24).
2 2 . . Open suction control, (page 20).
1 1 . . Change light bulb, (page 36).
1 1 . . Clean the power cord.
2 2 . . Pull out cord and rewind.
1 1 . . See VACUUMING TIPS, (page 30).
- 49 -