Intended Use; Safety Instructions - Ryobi RLS4A Traducción De Las Instrucciones Originales

Safety, performance and dependability have been given
top priority in the design of your electric log splitter.

INTENDED USE

The product is designed to split wooden material along the
grain. Logs or similar work pieces must be 20cm to 52cm
in length and 10cm to 25cm in diameter. The product must
be loaded, operated and cleared by one person only who is
without limitation in the physical abilities of the upper limbs.
The product is intended to be used only by persons who
have read and understood the operating instructions and
who are wearing adequate protective clothing as described
in the operating instructions. The product is intended to
instructions provided in the operating instruction manual.
Repairs to faulty or damaged parts of the product should
be carried out at an authorised service centre. The product
is intended to be used only in dry, well illuminated and
The product is not designed to split across the grain or for
used by children or persons who need supervision to safely
perform the actions required to operate this product.

SAFETY INSTRUCTIONS

WARNING
Read and understand all instructions. Failure to
follow all instructions listed below may result in electric
Keep work area clean. Cluttered areas and benches
invite accidents. Do not leave tools or pieces of wood
on the product while it is in operation.
Make sure the work area has ample lighting to see
the work and that no obstructions will interfere with
safe operation before using the product.
Do not use in dangerous environments. Do not use
Keep the work area well lit.
Keep the operator zone and adjacent area clear for
safe, secure footing.
Danger! Keep clear of moving parts.
Make sure the product is on a level surface.
log splitter as required in the manual instructions to
prevent unintended movement.
Make sure the product and any accessories are
properly installed and securely fastened.
Use the proper extension cord. Make sure your
extension cord is in good condition. Use only a
cord heavy enough to carry the current your product
will draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating.
Electrical power should be supplied via a residual
current device (RCD) with a tripping current of not
more than 30 mA.
Keep all bystanders, especially children and pets,
at least 15 m from the operating area.
Only one person is permitted to use the product.
Before use, examine the power cord or extension
cable for damage. If there are signs of damage, it must
be replaced by a qualified service technician.
Before use, check that there are no damaged parts.
A defective switch or any part that is damaged should
be properly repaired or replaced by an authorized
service facility.
Check damaged parts. Before further use of the
product, a guard or other part that is damaged should
be carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting and any other conditions
that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced by
an authorised service center.
Never leave the product running unattended. Turn
the power off. Do not leave the product until it comes
to a complete stop.
Never use in an explosive atmosphere. Normal
sparking of the motor could ignite fumes.
Dress properly. Do not wear loose clothing,
neckties, or jewelry that can get caught and draw
you into moving parts. Rubber gloves and nonskid
footwear are recommended when working outdoors.
Also wear protective hair covering to contain long hair.
To help reduce the risk of injury from falling work
pieces, the operator should wear footwear with
hardened toe protection.
Always wear safety glasses with side shields.
Everyday eyeglasses have only impact-resistant
lenses, they are not safety glasses.
Do not operate the product while under the
influence of drugs, alcohol, or any medication.
Disconnect from power outlet. When not in use,
before servicing, or when changing attachments,
blades, bits, cutters, etc., the product should be
disconnected from power source.
Maintain the product with care. Keep the log splitter
sharp and clean for better and safer performance.
Follow instructions for lubricating and changing
accessories.
Use recommended accessories.
operator's manual for recommended accessories. The
Product service must be performed only by
qualified repair personnel. Service or maintenance
performed by unqualified personnel could result in a
EN
English
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
Consult the
1