Protecting The Environment - Black and Decker ASI200-LA Manual De Instrucciones

f To switch between the different units (kPa, psi or bar),
press buttons 8 & 9 at the same time until the required
units are displayed.
f Press and hold button 8 or 9 for 3 seconds until the
display flashes.
f While the display is flashing press the - or + buttons
(8 & 9) until the required pressure is displayed.
f After 3 seconds the display will flash and return to a
reading of "0.0". This is normal.
f Connect the universal valve adaptor and accessories,
if required, to the item to be inflated, making sure that
the lever of the valve adaptor is in the down position to
lock it in place.
f To turn the inflator on, press the on/off switch (5) to
the I position.
f When the item to be inflated has reached the preset
value the unit will automatically turn off.
f To turn the inflator off press switch (5) to the 0 position.
f Remove the valve adaptor or accessory from the
inflated item and the 12 Volt adapter (6) from your
vehicle's 12 Volt accessory socket.
Note: If the 12 Volt adapter is removed from the
vehicles 12 Volt accessory socket, all settings will be lost
and will need to be re-entered following the instructions
under the heading 'Setting the required pressure
Operating the area light
f To operate the area light (1), make sure that the
12 Volt adaptor (6) is plugged into the vehicle's 12 Volt
accessory socket.
Note: Make sure that your 12 Volt accessory socket is live.
On some vehicles the accessory socket may only become
live when the ignition key is in the accessory position.
f To turn the area light on, press the area light on/ off
switch (7) located on the side of the unit to the I position.
f To turn the area light off, press the area light on/ off
switch (7) located on side of the unit to the 0 position.
To replace the bulb (Fig. F)
Warning! Make sure that the 12 Volt adaptor is not
connected before starting this procedure.
f Remove the screw (10) from the top of the lens cover(12).
f Pull the lens cover (12) down using the tab (11) to get
access to the bulb (13).
f To remove the bulb, push in and turn clockwise (Fig. F).
f Replace the bulb (13) with a one of the same type and
wattage (12V/5W).
f Fit the lens cover (12) and secure with the screw (10).
Using your inflator as a pressure gauge
f Make sure that the unit is powered as described in the
section 'Operating the Inflator'.
f Connect the universal valve adaptor and accessories
if required to the item to be inflated making sure that
the lever of the valve adaptor is in the down position to
lock it in place.
f The display will now show the actual pressure value
in the item.
MAINTENANCE
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on
corded/cordless power tools:
f Switch off and unplug the appliance/tool.
f Or switch off and remove the battery from the
appliance/ tool if the appliance/tool has a separate
battery pack.
f Or run the battery down completely if it is integral and
then switch off.
f Unplug the charger before cleaning it. Your charger
does not require any maintenance apart from regular
cleaning.
Regularly clean the ventilation slots in your appliance/ tool/
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Regularly open the valve adaptor and tap it to remove any
dust from the interior.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
Replacing the fuse in the vehicle dc accessory
plug
f Remove the cap by turning it counter-clockwise.
f Loosen the cap and centre pin.
f Remove the fuse.
f Fit a new fuse of the same type and size (8A/250V).
f Refit the cap and centre pin.
f Tighten the cap by turning clockwise onto the plug.

PROTECTING THE ENVIRONMENT

Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your BLACK+DECKER
product needs replacement, or if it is of no further
use to you, do not dispose of it with household
waste. Make this product available for separate
collection.
ENGLISH • 15