Peg-Perego John Deere BUCK EXT Empleo Y Manutencion página 7

ENGLISH
•PEG PEREGO® thanks you for choosing this product.
For over 50 years, PEG PEREGO has been taking
children for an outing: first with its famous baby
carriages and strollers, later with its pedal and
battery operated toy vehicles.
•Read this instruction manual carefully to learn the
use of this vehicle and to teach your child safe and
enjoyable driving. Please keep this manual for use
as a reference in the future.
•Our toys conform with the safety requirements
provided by the Council of the EEC, of the T.Ü.V.; of
the I.I.S.G. Istituto Italiano Sicurezza Giocattoli, and
the U.S. Consumer Toy Safety Specification F963.
Peg Perego S.p.A. is an ISO 9001
certified company.
The fact that we are certified provides
a guarantee of our honesty for our
customers, and fosters trust in the
company's way of working.
•Peg Perego reserves the right to modify or change
their product. Price, literature, manufacturing
processes or locations or any combination of these
above mentioned entities may change at any time
for any reason without notice with impunity.
Years 3-7
Weight capacity
85 lbs
CAUTION:
ELECTRIC VEHICLE NOT
RECOMMENDED FOR CHILDREN
UNDER 3 YEARS OF AGE. AS WITH
ALL ELECTRIC PRODUCTS,
PRECAUTIONS SHOULD BE
OBSERVED DURING HANDLING
AND USE TO PREVENT ELECTRIC
SHOCK. RECHARGER INCLUDED.120
VOLTS, 60Hz, 30W INPUT, 12 VOLTS
(DC) OUTPUT.
CUSTOMER SERVICE
PEG PEREGO offers after-sales services, directly or
through a network of authorized service centers for
repairs or replacement parts. See the back cover of
this instruction manual for contact information.
ASSEMBLY INSTRUCTIONS
CAUTION:
ADULT ASSEMBLY REQUIRED.
USE CARE WHEN UNPACKING AS
COMPONENTS TO BE ASSEMBLED
MAY POSE A SMALL PARTS/SHARP
EDGE HAZARD.
BATTERY ALREADY INSTALLED IN
VEHICLE.
ASSEMBLY
1 • Attach front grill/bumper by first hooking
eyelets on screw columns and then rotating
down into place.
2 • Secure front grill/bumper with 2 pins provided.
Insert one into the hole on each side.
3 • Align front rack with screw holes and fasten
with the 4 screws provided.
4 • To attach tailgate to rear of cargo bed, first
insert pivot rod into hole on one side (a), and
then push other side down into position (b).
5 • Insert spring into lift latch as shown in figure
(a). Then raise cargo bed and lift piston (b).
6 • Presslift latch down into position (a). Then align
holes on piston, latch and underside of cargo
bed and insert pin (b).
7 • Snap the nut cap into place and repeat the
operation on the other 3 wheels.
8 • Snap gas tank cap into place.
9 • Slip the handgrips onto the handlebars as
shown
10 • Loosen screw and remove battery door on
lower-left backside of handlebars (a).
Carefully pullout the battery tray and insert 2
AA batteries (b). (AA batteries not included
with the vehicle.) Replace tray and battery
door and tighten screw down.
11 • Snap the handlebar down into place on the
vehicle.
12 • Apply "speedometer" decal (#6) to handlebar.
13 • Place clear lens in bezel piece (a) and snap into
place over "speedometer" label (b).
14 • Apply 2 chrome decals to the headlight
positions on the front grill. See figure for proper
right/left placement.
15 • Snap the 2 clear headlights onto the front
grill over the chrome decals. See figure for
proper right/left placement.
16 • Apply 2 chrome decals in the taillight positions
on the rear bumper.
17 • Snap the 2 red taillights into place on the rear
bumper over the chrome decals.
INSTALLING BATTERY
CHARGE BATTERY BEFORE USING
18 • On the front of the vehicle, loosen screw on
front of battery compartment cover (a) and
detach rubber latches (b).
19 • Lift cover up and pull up and out.
20 • To remove metal retaining bar, first press back
on the right side (as seen in figure) until it
snaps free (a). Then slide bar right (b) until bar
clears left side and finally slide bar left and out
(c).
21 • Set battery tray down into compartment being
sure to insert pegs into holes.
22 • Set battery down into compartment and fit
securely into tray.
23 • Connect the battery wire plug to the
electrical system plug by aligning the two
ends as shown in the figure and pressing
together until it "snaps".
24 • To replace retaining bar, first insert bar into
right side and slide bar right (a) far
enough to allow left side to be inserted into
hole until it stops (b). Then pull back (toward
you) on right side until bar snaps into place
(c).
25 • Replace battery compartment cover,
reattach rubber latches and tighten screw
back down.
VEHICLE FEATURES AND INSTRUCTIONS FOR USE
26 • ACCELERATOR/BRAKE PEDAL: The vehicle will
automatically brake when the child takes
his/her foot off the accelerator.
27 • GEAR SHIFT LEVER: The vehicle has three
speeds. ATTENTION: When the vehicle is first
removed from the package, it only runs in first
gear (1) and reverse (R). (Note that reverse
mode is spring-loaded for safety.) To use the
second gear (2), proceed as follows:
28 • Loosen the screw and remove the tab as shown
in the figure.
29 • 1-R: The high speed lockout tab protrudes
from the column preventing the gearshift lever
from moving down into the second gear (a). 1-
2-R: The high speed lockout is removed and
the gearshift lever can be lowered into the
second gear (b).
30 • HORN: Press the button on the handlebar to
sound the horn.
REMOVING THE BATTERY
31 • Remove battery compartment cover and
retaining bar as explained in steps 20-22.
32 • Disconnect plug by pressing in on the sides of
the plugs and pulling apart.
33 • Lift battery out of compartment by the
handle.
34 • Set new battery down into compartment and
fit securely into tray.
35 • Connect the battery wire plug to the
electrical system plug.
36 • Replace retaining bar and battery
compartment cover, reattach rubber latches
and tighten screw back down.
BATTERY RECHARGE
WARNING:
WARNING: BATTERY CHARGING
AND ANY OTHER OPERATION ON
THE ELECTRICAL SYSTEM MUST BE
CARRIED OUT BY ADULTS ONLY.
THE BATTERY CAN ALSO BE CHARGED
WITHOUT REMOVING IT FROM THE
VEHICLE.
37 • Disconnect the electrical system plug (A)
from the battery wire plug (B) by pressing in
on the sides of the plugs.
38 • Plug the battery charger into a household
electrical outlet, following the instructions that
come with the battery charger. Connect plug B
to battery charger plug (C).
39 • After the battery has finished charging,
disconnect the battery charger from the
electrical outlet. Then disconnect plug C from
plug B.
40 • Press plug B all the way into plug A until it
snaps into place. After finishing this operation,
always remember to close and fasten the
battery compartment cover.
BATTERY MAINTENANCE
AND SAFETY
Before riding, charge your battery for
18 hours to initiate them. Failure to
do this will result in permanent
battery damage.
CAUTION:
Only adults should recharge batteries,
never children.
Never allow children to handle
batteries.
Only use the batteries specified by
the manufacturer.
Only use the charger specified by
the manufacturer.
Do not mix old and new batteries.
Do not mix alkaline, standard
(carbon-zinc), or rechargeable
(nickel-cadmium) batteries.
CHARGING THE BATTERY
• Charge the batteries no longer
than 24 hours, following the
instructions enclosed with the
battery charger.
• Charge the battery, as the vehicle
shows low power, in this way you
will avoid damage to the battery.
• If you don't use your vehicle for a
long period of time unplug the
battery from the main wire
harness of the vehicle. Remember
to charge the battery at least every
three months.
• Never charge the battery upside
down.
• Do not forget batteries during
charging! Check them periodically.
• Never use a replacement recharger
or batteries unless they are approved
by PEG PEREGO.
• Batteries are sealed and maintenance
free.
• Battery polarity must be observed
when connecting battery to
wiring.