Hourmeter - No Reset; Hourmeter - With Reset; Cord Sets And Connection Plugs; Vac,20 Amp, Gfci Duplex Receptacle - Generac XG4000 Serie Manual De Usuario

Operation

2.2 HOURMETER - NO RESET

The Hourmeter tracks hours of operation for scheduled
maintenance:
There will be a one time break in "CHG OIL" message that flashes
with the elapsed time in hours and tenths after the first 30 hours
of operation.
This message will actually begin flashing at 29 hours and disable
itself at 31 hours providing a two hour window to perform the
service.
There will be a subsequent "CHG OIL" message every 100 hours.
The message will flash one hour before and one hour after each
100 hour interval, again providing a two hour window to perform
service.
Every 200 hours the "SVC" icon on the lower left hand corner of
the display will flash. The message will flash one hour before and
one hour after each 200 hour interval providing a two hour window
to perform service.
When the hour meter is in the Flash Alert mode, the maintenance
message will always alternate with elapsed time in hours and
tenths. The hours will flash four times, then alternate with the
maintenance message four times until the meter resets itself.
• 100 hours - CHG OIL — Oil Change Interval (Every 100 hrs)
• 200 hours - SVC — Air Filter Interval (Every 200 hrs)

2.3 HOURMETER - WITH RESET

The Hourmeter tracks hours of operation for scheduled maintenance
(see chart).
Operation: Push and release the reset button to toggle between
screens. The hours count backwards from the set interval as
shown in the chart.
When the meter reaches 5 hours,the text "CHG OIL" (or "SVC AIR
FILTER" or "CHG PLUG") will flash continually for two minutes.
After this time, the meter will go back to displaying the total hours
of the unit (for 2 minutes). This cyle will repeat for the entire 5
hours.
When the service interval reaches zero hours, the text "NOW"
replaces the hours remaining.
Message
CHG OIL
CHG OIL
SVC AIR FILTER
CHG PLUG
6
Hourmeter (With Reset) Chart
Frequency of Message
Initial break-in period
Re-occuring
Re-occuring
Re-occuring
For a new generator for instance, the message will say "CHG OIL"
then flash "in 30". This means that in 30 hours, the oil will need to
be changed. Pressing the button a few more times will bring the
meter back to the screen that shows the total hours run.
Reset: Toggle to the alert that you wish to reset then hold the
button down for 9 seconds. The maintenance hours are reset when
the display shows "0000.0".
The hour glass graphic will flash on and off when the engine
is running. This signifies that the meter is tracking hours of
operation.
Figure 4 – Hourmeter
0000.0
HOUR GLASS
GRAPHIC

2.4 CORD SETS AND CONNECTION PLUGS

2.4.1 120 VAC, 20 AMP, GFCI DUPLEX RECEPTACLE
This is a 120 Volt outlet protected against overload by a 20 Amp
push-to-reset circuit breaker (Figure 5). Use each socket to power
120 Volt AC, single phase, 60 Hz electrical loads requiring up to a
combined 2400 watts (2.4 kW) or 20 Amps of current. Use only
high quality, well-insulated, 3-wire grounded cord sets rated for
125 Volts at 20 Amps (or greater). A cord set 15 feet or shorter
is preferred.
Keep extension cords as short as possible to prevent voltage drop
and possible overheating of wires.
Interval
First 30 Hours
100 hours
200 hours
200 hours
NOTE:
RESET BUTTON
(IF EQUIPPED)
Duration of message
ON/OFF for 2 minutes in a 5
hour period