Protecting The Environment - Black and Decker Powerful Solutions KC9006 Traducción De Las Instrucciones Originales

Always hold the tool and screwdriver bit in a straight line
with the screw.
When screwing in wood, it is recommended to drill a pilot
hole with a depth equal to the length of the screw. A pilot
hole guides the screw and prevents splintering or
distortion of the wood. For the optimum size of the pilot
hole, refer to the table below.
When screwing in hardwood, also drill a clearance hole
with a depth equal to half the length of the screw. For the
optimum size of the clearance hole, refer to the table
below.
Screw size Pilot hole ø
(softwood)
No. 6 (3.5 mm) 2.0 mm
No. 8 (4 mm) 3.2 mm
No. 10 (5 mm) 3.5 mm
Maintenance
Your Black & Decker corded/cordless appliance/tool has been
designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
switch off.
Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your appliance/tool/
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
from the interior (when fitted).

Protecting the environment

Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Pilot hole ø Clearance
(hardwood) hole
2.5 mm 4 mm
3.5 mm 5.0 mm
4.0 mm 5.7 mm
z
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand for
raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com
Batteries
Black & Decker batteries can be recharged many
times. At the end of their useful life, discard batteries
with due care for our environment:
Do not short-circuit the battery terminals.
Do not dispose of the battery(s) in a fire as this may result
in a risk of personal injury or an explosion.
Run the battery down completely, then remove it from the
tool.
Batteries are recyclable. Place the battery(s) in a suitable
packaging to ensure that the terminals cannot be
short-circuited. Take them to any authorised repair agent
or a local recycling station.
Technical data
Voltage
Battery size
No-load speed
Max. torque
Bit holder
Weight
Level of sound pressure according to EN 60745:
Sound pressure (L ) 57.2 dB(A), uncertainty (K) 3 dB(A)
pA
Sound power (L ) 68.2 dB(A), uncertainty (K) 3 dB(A)
WA
ENGLISH
KC9006 H1 / AS600 H1
V 6
DC
4 x LR06 (AA)
-1
min 130
Nm 2.9
6.35 mm hex
kg 0.24
7